; PJSIP Configuration Samples and Quick Reference ; ; This file has several very basic configuration examples, to serve as a quick ; reference to jog your memory when you need to write up a new configuration. ; It is not intended to teach PJSIP configuration or serve as an exhaustive ; reference of options and potential scenarios. ; ; This file has two main sections. ; First, manually written examples to serve as a handy reference. ; Second, a list of all possible PJSIP config options by section. This is ; pulled from the XML config help. It only shows the synopsis for every item. ; If you want to see more detail please check the documentation sources ; mentioned at the top of this file. ; Documentation ; ; The official documentation is at http://wiki.asterisk.org ; You can read the XML configuration help via Asterisk command line with ; "config show help res_pjsip", then you can drill down through the various ; sections and their options. ; ;========!!!!!!!!!!!!!!!!!!! SECURITY NOTICE !!!!!!!!!!!!!!!!!!!!=========== ; ; At a minimum please read the file "README-SERIOUSLY.bestpractices.txt", ; located in the Asterisk source directory before starting Asterisk. ; Otherwise you risk allowing the security of the Asterisk system to be ; compromised. Beyond that please visit and read the security information on ; the wiki at: https://wiki.asterisk.org/wiki/x/EwFB ; ; A few basics to pay attention to: ; ; Anonymous Calls ; ; By default anonymous inbound calls via PJSIP are not allowed. If you want to ; route anonymous calls you'll need to define an endpoint named "anonymous". ; res_pjsip_endpoint_identifier_anonymous.so handles that functionality so it ; must be loaded. It is not recommended to accept anonymous calls. ; ; Access Control Lists ; ; See the example ACL configuration in this file. Read the configuration help ; for the section and all of its options. Look over the samples in acl.conf ; and documentation at https://wiki.asterisk.org/wiki/x/uA80AQ ; If possible, restrict access to only networks and addresses you trust. ; ; Dialplan Contexts ; ; When defining configuration (such as an endpoint) that links into ; dialplan configuration, be aware of what that dialplan does. It's easy to ; accidentally provide access to internal or outbound dialing extensions which ; could cost you severely. The "context=" line in endpoint configuration ; determines which dialplan context inbound calls will enter into. ; ;============================================================================= ; Overview of Configuration Section Types Used in the Examples ; ; * Transport "transport" ; * Configures res_pjsip transport layer interaction. ; * Endpoint "endpoint" ; * Configures core SIP functionality related to SIP endpoints. ; * Authentication "auth" ; * Stores inbound or outbound authentication credentials for use by trunks, ; endpoints, registrations. ; * Address of Record "aor" ; * Stores contact information for use by endpoints. ; * Endpoint Identification "identify" ; * Maps a host directly to an endpoint ; * Access Control List "acl" ; * Defines a permission list or references one stored in acl.conf ; * Registration "registration" ; * Contains information about an outbound SIP registration ; The following sections show example configurations for various scenarios. ; Most require a couple or more configuration types configured in concert. ;============================================================================= ; Naming of Configuration Sections ; ; Configuration section names are denoted with enclosing brackets, ; e.g. [6001] ; In most cases, you can name a section whatever makes sense to you. For example ; you might name a transport [transport-udp-nat] to help you remember how that ; section is being used. However, in some cases, ("endpoint" and "aor" types) ; the section name has a relationship to its function. ; ; Depending on the modules loaded, Asterisk can match SIP requests to an ; endpoint or aor in a few ways: ; ; 1) Match a section name for endpoint type sections to the username in the ; "From" header of inbound SIP requests. ; 2) Match a section name for aor type sections to the username in the "To" ; header of inbound SIP REGISTER requests. ; 3) With an identify type section configured, match an inbound SIP request of ; any type to an endpoint or aor based on the IP source address of the ; request. ; ; Note that sections can have the same name as long as their "type" options are ; set to different values. In most cases it makes sense to have associated ; configuration sections use the same name, as you'll see in the examples within ; this file. ;===============EXAMPLE TRANSPORTS============================================ ; ; A few examples for potential transport options. ; ; For the NAT transport example, be aware that the options starting with ; the prefix "external_" will only apply to communication with addresses ; outside the range set with "local_net=". ; ; IPv6: For endpoints using IPv6, remember to set "rtp_ipv6=yes" so that the RTP ; engine will also be able to bind to an IPv6 address. ; ; You can have more than one of any type of transport, as long as it doesn't ; use the same resources (bind address, port, etc) as the others. ; Basic UDP transport ; ;[transport-udp] ;type=transport ;protocol=udp ;udp,tcp,tls,ws,wss ;bind=0.0.0.0 ; UDP transport behind NAT ; ;[transport-udp-nat] ;type=transport ;protocol=udp ;bind=0.0.0.0 ;local_net=192.0.2.0/24 ;external_media_address=203.0.113.1 ;external_signaling_address=203.0.113.1 ; Basic IPv6 UDP transport ; ;[transport-udp-ipv6] ;type=transport ;protocol=udp ;bind=:: ; Example IPv4 TLS transport ; ;[transport-tls] ;type=transport ;protocol=tls ;bind=0.0.0.0 ;cert_file=/path/mycert.crt ;priv_key_file=/path/mykey.key ;cipher=ALL ;method=tlsv1 ;===============OUTBOUND REGISTRATION WITH OUTBOUND AUTHENTICATION============ ; ; This is a simple registration that works with some SIP trunking providers. ; You'll need to set up the auth example "mytrunk_auth" below to enable outbound ; authentication. Note that we "outbound_auth=" use for outbound authentication ; instead of "auth=", which is for inbound authentication. ; ; If you are registering to a server from behind NAT, be sure you assign a transport ; that is appropriately configured with NAT related settings. See the NAT transport example. ; ; "contact_user=" sets the SIP contact header's user portion of the SIP URI ; this will affect the extension reached in dialplan when the far end calls you at this ; registration. The default is 's'. ;[mytrunk] ;type=registration ;transport=transport-udp ;outbound_auth=mytrunk_auth ;server_uri=sip:sip.example.com ;client_uri=sip:1234567890@sip.example.com ;contact_user=1234567890 ;retry_interval=60 ;forbidden_retry_interval=600 ;expiration=3600 ;[mytrunk_auth] ;type=auth ;auth_type=userpass ;password=1234567890 ;username=1234567890 ;realm=sip.example.com ;===============ENDPOINT CONFIGURED AS A TRUNK, OUTBOUND AUTHENTICATION======= ; ; This is one way to configure an endpoint as a trunk. It is set up with ; "outbound_auth=" to enable authentication when dialing out through this ; endpoint. There is no inbound authentication set up since a provider will ; not normally authenticate when calling you. ; ; The identify configuration enables IP address matching against this endpoint. ; For calls from a trunking provider, the From user may be different every time, ; so we want to match against IP address instead of From user. ; ; If you want the provider of your trunk to know where to send your calls ; you'll need to use an outbound registration as in the example above this ; section. ; ; NAT ; ; At a basic level configure the endpoint with a transport that is set up ; with the appropriate NAT settings. There may be some additional settings you ; need here based on your NAT/Firewall scenario. Look to the CLI config help ; "config show help res_pjsip endpoint" or on the wiki for other NAT related ; options and configuration. We've included a few below. ; ; AOR ; ; Endpoints use one or more AOR sections to store their contact details. ; You can define multiple contact addresses in SIP URI format in multiple ; "contact=" entries. ; ;[mytrunk] ;type=endpoint ;transport=transport-udp ;context=from-external ;disallow=all ;allow=ulaw ;outbound_auth=mytrunk_auth ;aors=mytrunk ; ;A few NAT relevant options that may come in handy. ;force_rport=yes ;It's a good idea to read the configuration help for each ;direct_media=no ;of these options. ;ice_support=yes ;[mytrunk] ;type=aor ;contact=sip:198.51.100.1:5060 ;contact=sip:198.51.100.2:5060 ;[mytrunk] ;type=identify ;endpoint=mytrunk ;match=198.51.100.1 ;match=198.51.100.2 ;=============ENDPOINT CONFIGURED AS A TRUNK, INBOUND AUTH AND REGISTRATION=== ; ; Here we are allowing a remote device to register to Asterisk and requiring ; that they authenticate for registration and calls. ; You'll note that this configuration is essentially the same as configuring ; an endpoint for use with a SIP phone. ;[7000] ;type=endpoint ;context=from-external ;disallow=all ;allow=ulaw ;transport=transport-udp ;auth=7000 ;aors=7000 ;[7000] ;type=auth ;auth_type=userpass ;password=7000 ;username=7000 ;[7000] ;type=aor ;max_contacts=1 ;===============ENDPOINT CONFIGURED FOR USE WITH A SIP PHONE================== ; ; This example includes the endpoint, auth and aor configurations. It ; requires inbound authentication and allows registration, as well as references ; a transport that you'll need to uncomment from the previous examples. ; ; Uncomment one of the transport lines to choose which transport you want. If ; not specified then the default transport chosen is the first defined transport ; in the configuration file. ; ; Modify the "max_contacts=" line to change how many unique registrations to allow. ; ; Use the "contact=" line instead of max_contacts= if you want to statically ; define the location of the device. ; ; If using the TLS enabled transport, you may want the "media_encryption=sdes" ; option to additionally enable SRTP, though they are not mutually inclusive. ; ; Use the "rtp_ipv6=yes" option if you want to utilize RTP over an ipv6 transport. ; ; If this endpoint were remote, and it was using a transport configured for NAT ; then you likely want to use "direct_media=no" to prevent audio issues. ;[6001] ;type=endpoint ;transport=transport-udp ;context=from-internal ;disallow=all ;allow=ulaw ;allow=gsm ;auth=6001 ;aors=6001 ; ; A few more transports to pick from, and some related options below them. ; ;transport=transport-tls ;media_encryption=sdes ;transport=transport-udp-ipv6 ;rtp_ipv6=yes ;transport=transport-udp-nat ;direct_media=no ; ; MWI related options ;aggregate_mwi=yes ;mailboxes=6001@default,7001@default ;mwi_from_user=6001 ; ; Extension and Device state options ; ;device_state_busy_at=1 ;allow_subscribe=yes ;sub_min_expiry=30 ;[6001] ;type=auth ;auth_type=userpass ;password=6001 ;username=6001 ;[6001] ;type=aor ;max_contacts=1 ;contact=sip:6001@192.0.2.1:5060 ;===============ENDPOINT BEHIND NAT OR FIREWALL=============================== ; ; This example assumes your transport is configured with a public IP and the ; endpoint itself is behind NAT and maybe a firewall, rather than having ; Asterisk behind NAT. For the sake of simplicity, we'll assume a typical ; VOIP phone. The most important settings to configure are: ; ; * direct_media, to ensure Asterisk stays in the media path ; * rtp_symmetric and force_rport options to help the far-end NAT/firewall ; ; Depending on the settings of your remote SIP device or NAT/firewall device ; you may have to experiment with a combination of these settings. ; ; If both Asterisk and the remote phones are a behind NAT/firewall then you'll ; have to make sure to use a transport with appropriate settings (as in the ; transport-udp-nat example). ; ;[6002] ;type=endpoint ;transport=transport-udp ;context=from-internal ;disallow=all ;allow=ulaw ;auth=6002 ;aors=6002 ;direct_media=no ;rtp_symmetric=yes ;force_rport=yes ;ice_support=yes ;This is specific to clients that support NAT traversal ;for media via ICE,STUN,TURN. See the wiki at: ;https://wiki.asterisk.org/wiki/x/D4FHAQ ;for a deeper explanation of this topic. ;[6002] ;type=auth ;auth_type=userpass ;password=6002 ;username=6002 ;[6002] ;type=aor ;max_contacts=2 ;============EXAMPLE ACL CONFIGURATION========================================== ; ; The ACL or Access Control List section defines a set of permissions to permit ; or deny access to various address or addresses. Alternatively it references an ; ACL configuration already set in acl.conf. ; ; The ACL configuration is independent of individual endpoint configuration and ; operates on all inbound SIP communication using res_pjsip. ; Reference an ACL defined in acl.conf. ; ;[acl] ;type=acl ;acl=example_named_acl1 ; Reference a contactacl specifically. ; ;[acl] ;type=acl ;contact_acl=example_contact_acl1 ; Define your own ACL here in pjsip.conf and ; permit or deny by IP address or range. ; ;[acl] ;type=acl ;deny=0.0.0.0/0.0.0.0 ;permit=209.16.236.0/24 ;deny=209.16.236.1 ; Restrict based on Contact Headers rather than IP. ; Define options multiple times for various addresses or use a comma-delimited string. ; ;[acl] ;type=acl ;contact_deny=0.0.0.0/0.0.0.0 ;contact_permit=209.16.236.0/24 ;contact_permit=209.16.236.1 ;contact_permit=209.16.236.2,209.16.236.3 ; Restrict based on Contact Headers rather than IP and use ; advanced syntax. Note the bang symbol used for "NOT", so we can deny ; 209.16.236.12/32 within the permit= statement. ; ;[acl] ;type=acl ;contact_deny=0.0.0.0/0.0.0.0 ;contact_permit=209.16.236.0 ;permit=209.16.236.0/24, !209.16.236.12/32 ; MODULE PROVIDING BELOW SECTION(S): res_pjsip ;==========================ENDPOINT SECTION OPTIONS========================= ;[endpoint] ; SYNOPSIS: Endpoint ;100rel=yes ; Allow support for RFC3262 provisional ACK tags (default: ; "yes") ;aggregate_mwi=yes ; (default: "yes") ;allow= ; Media Codec s to allow (default: "") ;aors= ; AoR s to be used with the endpoint (default: "") ;auth= ; Authentication Object s associated with the endpoint (default: "") ;callerid= ; CallerID information for the endpoint (default: "") ;callerid_privacy= ; Default privacy level (default: "") ;callerid_tag= ; Internal id_tag for the endpoint (default: "") ;context=default ; Dialplan context for inbound sessions (default: ; "default") ;direct_media_glare_mitigation=none ; Mitigation of direct media re INVITE ; glare (default: "none") ;direct_media_method=invite ; Direct Media method type (default: "invite") ;connected_line_method=invite ; Connected line method type (default: ; "invite") ;direct_media=yes ; Determines whether media may flow directly between ; endpoints (default: "yes") ;disable_direct_media_on_nat=no ; Disable direct media session refreshes when ; NAT obstructs the media session (default: ; "no") ;disallow= ; Media Codec s to disallow (default: "") ;dtmf_mode=rfc4733 ; DTMF mode (default: "rfc4733") ;media_address= ; IP address used in SDP for media handling (default: "") ;force_rport=yes ; Force use of return port (default: "yes") ;ice_support=no ; Enable the ICE mechanism to help traverse NAT (default: "no") ;identify_by=username ; Way s for Endpoint to be identified (default: ; "username") ;redirect_method=user ; How redirects received from an endpoint are handled ; (default: "user") ;mailboxes= ; Mailbox es to be associated with (default: "") ;moh_suggest=default ; Default Music On Hold class (default: "default") ;outbound_auth= ; Authentication object used for outbound requests (default: ; "") ;outbound_proxy= ; Proxy through which to send requests a full SIP URI ; must be provided (default: "") ;rewrite_contact=no ; Allow Contact header to be rewritten with the source ; IP address port (default: "no") ;rtp_ipv6=no ; Allow use of IPv6 for RTP traffic (default: "no") ;rtp_symmetric=no ; Enforce that RTP must be symmetric (default: "no") ;send_diversion=yes ; Send the Diversion header conveying the diversion ; information to the called user agent (default: "yes") ;send_pai=no ; Send the P Asserted Identity header (default: "no") ;send_rpid=no ; Send the Remote Party ID header (default: "no") ;timers_min_se=90 ; Minimum session timers expiration period (default: ; "90") ;timers=yes ; Session timers for SIP packets (default: "yes") ;timers_sess_expires=1800 ; Maximum session timer expiration period ; (default: "1800") ;transport= ; Desired transport configuration (default: "") ;trust_id_inbound=no ; Accept identification information received from this ; endpoint (default: "no") ;trust_id_outbound=no ; Send private identification details to the endpoint ; (default: "no") ;type= ; Must be of type endpoint (default: "") ;use_ptime=no ; Use Endpoint s requested packetisation interval (default: ; "no") ;use_avpf=no ; Determines whether res_pjsip will use and enforce usage of ; AVPF for this endpoint (default: "no") ;media_encryption=no ; Determines whether res_pjsip will use and enforce ; usage of media encryption for this endpoint (default: ; "no") ;inband_progress=no ; Determines whether chan_pjsip will indicate ringing ; using inband progress (default: "no") ;call_group= ; The numeric pickup groups for a channel (default: "") ;pickup_group= ; The numeric pickup groups that a channel can pickup (default: ; "") ;named_call_group= ; The named pickup groups for a channel (default: "") ;named_pickup_group= ; The named pickup groups that a channel can pickup ; (default: "") ;device_state_busy_at=0 ; The number of in use channels which will cause busy ; to be returned as device state (default: "0") ;t38_udptl=no ; Whether T 38 UDPTL support is enabled or not (default: "no") ;t38_udptl_ec=none ; T 38 UDPTL error correction method (default: "none") ;t38_udptl_maxdatagram=0 ; T 38 UDPTL maximum datagram size (default: ; "0") ;fax_detect=no ; Whether CNG tone detection is enabled (default: "no") ;t38_udptl_nat=no ; Whether NAT support is enabled on UDPTL sessions ; (default: "no") ;t38_udptl_ipv6=no ; Whether IPv6 is used for UDPTL Sessions (default: ; "no") ;tone_zone= ; Set which country s indications to use for channels created ; for this endpoint (default: "") ;language= ; Set the default language to use for channels created for this ; endpoint (default: "") ;one_touch_recording=no ; Determines whether one touch recording is allowed for ; this endpoint (default: "no") ;record_on_feature=automixmon ; The feature to enact when one touch recording ; is turned on (default: "automixmon") ;record_off_feature=automixmon ; The feature to enact when one touch recording ; is turned off (default: "automixmon") ;rtp_engine=asterisk ; Name of the RTP engine to use for channels created ; for this endpoint (default: "asterisk") ;allow_transfer=yes ; Determines whether SIP REFER transfers are allowed ; for this endpoint (default: "yes") ;sdp_owner=- ; String placed as the username portion of an SDP origin o line ; (default: "-") ;sdp_session=Asterisk ; String used for the SDP session s line (default: ; "Asterisk") ;tos_audio=0 ; DSCP TOS bits for audio streams (default: "0") ;tos_video=0 ; DSCP TOS bits for video streams (default: "0") ;cos_audio=0 ; Priority for audio streams (default: "0") ;cos_video=0 ; Priority for video streams (default: "0") ;allow_subscribe=yes ; Determines if endpoint is allowed to initiate ; subscriptions with Asterisk (default: "yes") ;sub_min_expiry=0 ; The minimum allowed expiry time for subscriptions ; initiated by the endpoint (default: "0") ;from_user= ; Username to use in From header for requests to this endpoint ; (default: "") ;mwi_from_user= ; Username to use in From header for unsolicited MWI NOTIFYs to ; this endpoint (default: "") ;from_domain= ; Domain to user in From header for requests to this endpoint ; (default: "") ;dtls_verify= ; Verify that the provided peer certificate is valid (default: ; "") ;dtls_rekey= ; Interval at which to renegotiate the TLS session and rekey ; the SRTP session (default: "") ;dtls_cert_file= ; Path to certificate file to present to peer (default: ; "") ;dtls_private_key= ; Path to private key for certificate file (default: ; "") ;dtls_cipher= ; Cipher to use for DTLS negotiation (default: "") ;dtls_ca_file= ; Path to certificate authority certificate (default: "") ;dtls_ca_path= ; Path to a directory containing certificate authority ; certificates (default: "") ;dtls_setup= ; Whether we are willing to accept connections connect to the ; other party or both (default: "") ;srtp_tag_32=no ; Determines whether 32 byte tags should be used instead of 80 ; byte tags (default: "no") ;set_var= ; Variable set on a channel involving the endpoint. For multiple ; channel variables specify multiple 'set_var'(s) ;==========================AUTH SECTION OPTIONS========================= ;[auth] ; SYNOPSIS: Authentication type ;auth_type=userpass ; Authentication type (default: "userpass") ;nonce_lifetime=32 ; Lifetime of a nonce associated with this ; authentication config (default: "32") ;md5_cred= ; MD5 Hash used for authentication (default: "") ;password= ; PlainText password used for authentication (default: "") ;realm= ; SIP realm for endpoint (default: "") ;type= ; Must be auth (default: "") ;username= ; Username to use for account (default: "") ;==========================DOMAIN_ALIAS SECTION OPTIONS========================= ;[domain_alias] ; SYNOPSIS: Domain Alias ;type= ; Must be of type domain_alias (default: "") ;domain= ; Domain to be aliased (default: "") ;==========================TRANSPORT SECTION OPTIONS========================= ;[transport] ; SYNOPSIS: SIP Transport ;async_operations=1 ; Number of simultaneous Asynchronous Operations ; (default: "1") ;bind= ; IP Address and optional port to bind to for this transport (default: ; "") ;ca_list_file= ; File containing a list of certificates to read TLS ONLY ; (default: "") ;cert_file= ; Certificate file for endpoint TLS ONLY (default: "") ;cipher= ; Preferred Cryptography Cipher TLS ONLY (default: "") ;domain= ; Domain the transport comes from (default: "") ;external_media_address= ; External IP address to use in RTP handling ; (default: "") ;external_signaling_address= ; External address for SIP signalling (default: ; "") ;external_signaling_port=0 ; External port for SIP signalling (default: ; "0") ;method= ; Method of SSL transport TLS ONLY (default: "") ;local_net= ; Network to consider local used for NAT purposes (default: "") ;password= ; Password required for transport (default: "") ;priv_key_file= ; Private key file TLS ONLY (default: "") ;protocol=udp ; Protocol to use for SIP traffic (default: "udp") ;require_client_cert= ; Require client certificate TLS ONLY (default: "") ;type= ; Must be of type transport (default: "") ;verify_client= ; Require verification of client certificate TLS ONLY (default: ; "") ;verify_server= ; Require verification of server certificate TLS ONLY (default: ; "") ;tos=0 ; Enable TOS for the signalling sent over this transport (default: "0") ;cos=0 ; Enable COS for the signalling sent over this transport (default: "0") ;websocket_write_timeout=100 ; Default write timeout to set on websocket ; transports. This value may need to be adjusted ; for connections where Asterisk must write a ; substantial amount of data and the receiving ; clients are slow to process the received ; information. Value is in milliseconds; default ; is 100 ms. ;==========================CONTACT SECTION OPTIONS========================= ;[contact] ; SYNOPSIS: A way of creating an aliased name to a SIP URI ;type= ; Must be of type contact (default: "") ;uri= ; SIP URI to contact peer (default: "") ;expiration_time= ; Time to keep alive a contact (default: "") ;qualify_frequency=0 ; Interval at which to qualify a contact (default: "0") ;outbound_proxy= ; Outbound proxy used when sending OPTIONS request ; (default: "") ;==========================AOR SECTION OPTIONS========================= ;[aor] ; SYNOPSIS: The configuration for a location of an endpoint ;contact= ; Permanent contacts assigned to AoR (default: "") ;default_expiration=3600 ; Default expiration time in seconds for ; contacts that are dynamically bound to an AoR ; (default: "3600") ;mailboxes= ; Mailbox es to be associated with (default: "") ;maximum_expiration=7200 ; Maximum time to keep an AoR (default: "7200") ;max_contacts=0 ; Maximum number of contacts that can bind to an AoR (default: ; "0") ;minimum_expiration=60 ; Minimum keep alive time for an AoR (default: "60") ;remove_existing=no ; Determines whether new contacts replace existing ones ; (default: "no") ;type= ; Must be of type aor (default: "") ;qualify_frequency=0 ; Interval at which to qualify an AoR (default: "0") ;authenticate_qualify=no ; Authenticates a qualify request if needed ; (default: "no") ;outbound_proxy= ; Outbound proxy used when sending OPTIONS request ; (default: "") ;==========================SYSTEM SECTION OPTIONS========================= ;[system] ; SYNOPSIS: Options that apply to the SIP stack as well as other system-wide settings ;timer_t1=500 ; Set transaction timer T1 value milliseconds (default: "500") ;timer_b=32000 ; Set transaction timer B value milliseconds (default: "32000") ;compact_headers=no ; Use the short forms of common SIP header names ; (default: "no") ;threadpool_initial_size=0 ; Initial number of threads in the res_pjsip ; threadpool (default: "0") ;threadpool_auto_increment=5 ; The amount by which the number of threads is ; incremented when necessary (default: "5") ;threadpool_idle_timeout=60 ; Number of seconds before an idle thread ; should be disposed of (default: "60") ;threadpool_max_size=0 ; Maximum number of threads in the res_pjsip threadpool ; A value of 0 indicates no maximum (default: "0") ;type= ; Must be of type system (default: "") ;==========================GLOBAL SECTION OPTIONS========================= ;[global] ; SYNOPSIS: Options that apply globally to all SIP communications ;max_forwards=70 ; Value used in Max Forwards header for SIP requests ; (default: "70") ;type= ; Must be of type global (default: "") ;user_agent=Asterisk PBX SVN-branch-12-r404375 ; Value used in User Agent ; header for SIP requests and ; Server header for SIP ; responses (default: "Asterisk ; PBX SVN-branch-12-r404375") ;default_outbound_endpoint=default_outbound_endpoint ; Endpoint to use when ; sending an outbound ; request to a URI ; without a specified ; endpoint (default: "d ; efault_outbound_endpo ; int") ;debug=no ; Enable/Disable SIP debug logging. Valid options include yes|no ; or a host address (default: "no") ; MODULE PROVIDING BELOW SECTION(S): res_pjsip_acl ;==========================ACL SECTION OPTIONS========================= ;[acl] ; SYNOPSIS: Access Control List ;acl= ; List of IP ACL section names in acl conf (default: "") ;contact_acl= ; List of Contact ACL section names in acl conf (default: "") ;contact_deny= ; List of Contact header addresses to deny (default: "") ;contact_permit= ; List of Contact header addresses to permit (default: ; "") ;deny= ; List of IP addresses to deny access from (default: "") ;permit= ; List of IP addresses to permit access from (default: "") ;type= ; Must be of type acl (default: "") ; MODULE PROVIDING BELOW SECTION(S): res_pjsip_outbound_registration ;==========================REGISTRATION SECTION OPTIONS========================= ;[registration] ; SYNOPSIS: The configuration for outbound registration ;auth_rejection_permanent=yes ; Determines whether failed authentication ; challenges are treated as permanent failures ; (default: "yes") ;client_uri= ; Client SIP URI used when attemping outbound registration ; (default: "") ;contact_user= ; Contact User to use in request (default: "") ;expiration=3600 ; Expiration time for registrations in seconds ; (default: "3600") ;max_retries=10 ; Maximum number of registration attempts (default: "10") ;outbound_auth= ; Authentication object to be used for outbound registrations ; (default: "") ;outbound_proxy= ; Outbound Proxy used to send registrations (default: ; "") ;retry_interval=60 ; Interval in seconds between retries if outbound ; registration is unsuccessful (default: "60") ;forbidden_retry_interval=0 ; Interval used when receiving a 403 Forbidden ; response (default: "0") ;server_uri= ; SIP URI of the server to register against (default: "") ;transport= ; Transport used for outbound authentication (default: "") ;type= ; Must be of type registration (default: "") ; MODULE PROVIDING BELOW SECTION(S): res_pjsip_endpoint_identifier_ip ;==========================IDENTIFY SECTION OPTIONS========================= ;[identify] ; SYNOPSIS: Identifies endpoints via source IP address ;endpoint= ; Name of Endpoint (default: "") ;match= ; IP addresses or networks to match against (default: "") ;type= ; Must be of type identify (default: "")