| Age | Commit message (Collapse) | Author |
|---|
|
* A driver reload should reset Astribank hardware
* This patch send an SPI reset after we get AB_DESCRIPTION reply from Astribank
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10474 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Here it is:
KERNEL_STYLE="-npro -kr -i8 -ts8 -sob -l80 -ss -ncs -cp1"
TYPEDEFS='
-T gfp_t
-T __user
-T u_char
-T __u8
-T byte
-T bool
-T charp
-T xusb_t
-T xbus_t
-T xpd_t
-T xproto_table_t
-T xproto_entry_t
-T xframe_t
-T xpacket_t
-T reg_cmd_t
'
indent $TYPEDEFS $KERNEL_STYLE \
--ignore-newlines \
--indent-label0 \
--no-space-after-function-call-names \
"$@"
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10428 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Applied via:
perl -pi \
-e '/"/ and next;' \
-e '/^\s*\*/ and next;' \
-e '/\/\*.*byte/ and next;' \
-e '/typedef.*byte/ and next;' \
-e 's/\bbyte\b/__u8/g' "$@"
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10427 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
OLD_PROC marked old and unused code that was used for writing to procfs.
It has long ago been replaced with different sysfs interfaces. Time
to remove it.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9916 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Fix cases where the command_queue overflowed during initialization.
- Also add a 'command_queue_length' parameter to xpp.ko
* More migrations to sysfs:
- Add a 'transport' attribute to our astribank devices which
points to the usb device we use. E.g:
/sys/bus/astribanks/devices/xbus-00/transport is symlinked to
../../../../../../devices/pci0000:00/0000:00:10.4/usb5/5-4
- Move /proc/xpp/XBUS-??/XPD-??/span to
/sys/bus/xpds/devices/??:?:?/span
- Migrate from /proc/xpp/sync to:
/sys/bus/astribanks/drivers/xppdrv/sync
- New 'offhook' attribute in:
/sys/bus/xpds/devices/??:?:?/offhook
* PRI: change the "timing" priority to match the convention used by
other PRI cards -- I.e: lower numbers (not 0) have higher
priority.
* FXO:
- Power denial: create two module parameters instead of hard-coded
constants (power_denial_safezone, power_denial_minlen).
For sites that get non-standard power-denial signals from central
office on offhook.
- Don't hangup on power-denial, just notify Dahdi and wait for
- Fix caller-id detection for the case central office sends it before
first ring without any indication before.
Asterisk's desicion.
* USB_FW.hex:
- Fixes cases where firmware loading would fail.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@6046 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Sysfs representation for XPDs:
/sys/bus/xpds/devices/<bus>:<unit>:<subunit>
* Astribanks sysfs directories now include the XPDs as subdirectories:
e.g. /sys/bus/astribanks/devices/xbus-00/00:3:0
* procfs control interface deprecated: conditioned by OLD_PROC
(defaults to off). Control functionality moved to sysfs:
* xbus attributes: cls connector label status timing waitfor_xpds xbus_state
* XPDs can have driver-specific attributes. Common attriubtes:
blink chipregs span
* PRI-specific attributes:
pri_clocking pri_dchan pri_cas pri_alarms pri_layer1 pri_localloop pri_protocol
* The Astribank attribute "xbus_state" is read/write. Reading it shows
the current state of the Astribank. Writing "start" or "stop" allows a
software equivalent of connect or disconnect respectively.
* When an Astribank is ready it sends an "online" event. Whenever its
not ready (e.g. at the time of disconnect) it sends an "offline" event.
Use astribank_hook.sample to handle those.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@5097 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4315 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
