| Age | Commit message (Collapse) | Author |
|---|
|
* Demote some messages to be debug messages.
* Rephrase the message about defaults for the PRI module (the driver's
defaults are used, which is OK)
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@6135 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Fix cases where the command_queue overflowed during initialization.
- Also add a 'command_queue_length' parameter to xpp.ko
* More migrations to sysfs:
- Add a 'transport' attribute to our astribank devices which
points to the usb device we use. E.g:
/sys/bus/astribanks/devices/xbus-00/transport is symlinked to
../../../../../../devices/pci0000:00/0000:00:10.4/usb5/5-4
- Move /proc/xpp/XBUS-??/XPD-??/span to
/sys/bus/xpds/devices/??:?:?/span
- Migrate from /proc/xpp/sync to:
/sys/bus/astribanks/drivers/xppdrv/sync
- New 'offhook' attribute in:
/sys/bus/xpds/devices/??:?:?/offhook
* PRI: change the "timing" priority to match the convention used by
other PRI cards -- I.e: lower numbers (not 0) have higher
priority.
* FXO:
- Power denial: create two module parameters instead of hard-coded
constants (power_denial_safezone, power_denial_minlen).
For sites that get non-standard power-denial signals from central
office on offhook.
- Don't hangup on power-denial, just notify Dahdi and wait for
- Fix caller-id detection for the case central office sends it before
first ring without any indication before.
Asterisk's desicion.
* USB_FW.hex:
- Fixes cases where firmware loading would fail.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@6046 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Fix cases where the command_queue overflowed during initialization.
* More migrations to sysfs:
- Add a 'transport' attribute to our astribank devices which
points to the usb device we use. E.g:
/sys/bus/astribanks/devices/xbus-00/transport is symlinked to
../../../../../../devices/pci0000:00/0000:00:10.4/usb5/5-4
- Move /proc/xpp/XBUS-??/XPD-??/span to
/sys/bus/xpds/devices/??:?:?/span
- Migrate from /proc/xpp/sync to:
/sys/bus/astribanks/drivers/xppdrv/sync
* PRI: change the "timing" priority to match the convention used by
other PRI cards -- I.e: lower numbers (not 0) have higher
priority.
* FXO:
- Power denial: create two module parameters instead of hard-coded
constants (power_denial_safezone, power_denial_minlen).
For sites that get non-standard power-denial signals from central
office on offhook.
- Don't hangup on power-denial, just notify Dahdi and wait for
- Fix caller-id detection for the case central office sends it before
first ring without any indication before.
Asterisk's desicion.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@5663 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Sysfs representation for XPDs:
/sys/bus/xpds/devices/<bus>:<unit>:<subunit>
* Astribanks sysfs directories now include the XPDs as subdirectories:
e.g. /sys/bus/astribanks/devices/xbus-00/00:3:0
* procfs control interface deprecated: conditioned by OLD_PROC
(defaults to off). Control functionality moved to sysfs:
* xbus attributes: cls connector label status timing waitfor_xpds xbus_state
* XPDs can have driver-specific attributes. Common attriubtes:
blink chipregs span
* PRI-specific attributes:
pri_clocking pri_dchan pri_cas pri_alarms pri_layer1 pri_localloop pri_protocol
* The Astribank attribute "xbus_state" is read/write. Reading it shows
the current state of the Astribank. Writing "start" or "stop" allows a
software equivalent of connect or disconnect respectively.
* When an Astribank is ready it sends an "online" event. Whenever its
not ready (e.g. at the time of disconnect) it sends an "offline" event.
Use astribank_hook.sample to handle those.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@5097 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* This commit fixes display of indirect registers through the chipregs
(formly "slics") procfs file. Only the low byte was displayed.
* It also deprecates previous {RW}S in favour of {RW}I. The prevois
style is still allowed but deprecated, and thus previous scripts will
still work.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4980 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* More complete Kconfig.
* Verification of FXO init script moved here from tools.
* Perl init scripts are verified.
* Correct name XppConf*ig*.
* Add the files for xpp_mmap .
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4408 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4315 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
