| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9709 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Fixes a regression singce r8873: if pri_protocol is not explicitly set
(in /etc/dahdi/xpp.conf) and the device has (licences for) less than 4
"PRI" (E1/T1) ports, the initialization script will attempt to read from
a non-existing SysFS file, and bail out, resulting in a the device
failing to initialize.
For those non-existing ports we can just skip that part of the
initialization. So we just skip it.
Work around: explicitly set pri_protocol to E1 or T1, as needed.
Xorcom Rev: 8047. Ticket: 1334.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9430 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
This avoids most cases of sending garbage at startup by setting each port
to tristate mode at init time (in the init script) and enable it back at
DAHDI_STARTUO (end of dahdi_cfg).
Upgrade note: if you have upgraded the files (including init script) but old
module is still loaded, you may end up with the port not getting ever
enabled and the line practically dead. In such a case, reload the new module.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@8922 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
When initializing registers for the "PRI" (E1/T1) module, in the case the
user has not explicitly asked for E1/T1 settings in xpp.conf (pri_protocol)
fall back to the current value, which is the build-time fall-back.
The value is read from sysfs.
Previously we implicitly assumed this value is E1.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@8873 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@8872 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@7266 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Demote some messages to be debug messages.
* Rephrase the message about defaults for the PRI module (the driver's
defaults are used, which is OK)
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@6135 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Fix cases where the command_queue overflowed during initialization.
* More migrations to sysfs:
- Add a 'transport' attribute to our astribank devices which
points to the usb device we use. E.g:
/sys/bus/astribanks/devices/xbus-00/transport is symlinked to
../../../../../../devices/pci0000:00/0000:00:10.4/usb5/5-4
- Move /proc/xpp/XBUS-??/XPD-??/span to
/sys/bus/xpds/devices/??:?:?/span
- Migrate from /proc/xpp/sync to:
/sys/bus/astribanks/drivers/xppdrv/sync
* PRI: change the "timing" priority to match the convention used by
other PRI cards -- I.e: lower numbers (not 0) have higher
priority.
* FXO:
- Power denial: create two module parameters instead of hard-coded
constants (power_denial_safezone, power_denial_minlen).
For sites that get non-standard power-denial signals from central
office on offhook.
- Don't hangup on power-denial, just notify Dahdi and wait for
- Fix caller-id detection for the case central office sends it before
first ring without any indication before.
Asterisk's desicion.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@5663 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Clock synchronization when sync is not from first port.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@5320 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Sysfs representation for XPDs:
/sys/bus/xpds/devices/<bus>:<unit>:<subunit>
* Astribanks sysfs directories now include the XPDs as subdirectories:
e.g. /sys/bus/astribanks/devices/xbus-00/00:3:0
* procfs control interface deprecated: conditioned by OLD_PROC
(defaults to off). Control functionality moved to sysfs:
* xbus attributes: cls connector label status timing waitfor_xpds xbus_state
* XPDs can have driver-specific attributes. Common attriubtes:
blink chipregs span
* PRI-specific attributes:
pri_clocking pri_dchan pri_cas pri_alarms pri_layer1 pri_localloop pri_protocol
* The Astribank attribute "xbus_state" is read/write. Reading it shows
the current state of the Astribank. Writing "start" or "stop" allows a
software equivalent of connect or disconnect respectively.
* When an Astribank is ready it sends an "online" event. Whenever its
not ready (e.g. at the time of disconnect) it sends an "offline" event.
Use astribank_hook.sample to handle those.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@5097 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* The configuration for XPP init_card_* scripts is done now
in /etc/dahdi/xpp.conf and uses a simple syntax (example included).
For PRI modules, the 'pri_protocol' setting, determines how
to configure it (E1/T1).
* In Astribank PRI modules, the LED behaviour represent which ports
are *CLOCK MASTER* (red color) and which are *CLOCK SLAVE* (green color).
Usually (but not always), this corresponds to the NT/TE settings in Asterisk.
* dahdi_genconf now replaces zapconf and deprecates genzaptelconf.
Relevant configuration settings were removed from the kernel
package and are implemented and described in the tools package.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4480 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* More complete Kconfig.
* Verification of FXO init script moved here from tools.
* Perl init scripts are verified.
* Correct name XppConf*ig*.
* Add the files for xpp_mmap .
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4408 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* No more dependency in zconf/
* Add new config file: xpp.conf
* Use new perl module XppConfig.pm that read this config file.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4373 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@4315 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
