/* * Digium, Inc. Wildcard TE110P T1/PRI card Driver * * Written by Mark Spencer * Matthew Fredrickson * William Meadows * * Copyright (C) 2004, Digium, Inc. * * All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * * $Id$ */ #include #include #include #include #include #include #include #include #ifdef STANDALONE_ZAPATA #include "zaptel.h" #else #include #endif #ifdef LINUX26 #include #endif #include "wct4xxp.h" /* For certain definitions */ #define WC_MAX_CARDS 32 /* #define TEST_REGS */ /* Define to get more attention-grabbing but slightly more I/O using alarm status */ #define FANCY_ALARM /* Define to enable the V2.1 errata register settings */ #if 0 #define TRUST_INFINEON_ERRATA #endif #define DELAY 0x0 /* 30 = 15 cycles, 10 = 8 cycles, 0 = 3 cycles */ #define WC_CNTL 0x00 #define WC_OPER 0x01 #define WC_AUXC 0x02 #define WC_AUXD 0x03 #define WC_MASK0 0x04 #define WC_MASK1 0x05 #define WC_INTSTAT 0x06 #define WC_DMAWS 0x08 #define WC_DMAWI 0x0c #define WC_DMAWE 0x10 #define WC_DMARS 0x18 #define WC_DMARI 0x1c #define WC_DMARE 0x20 #define WC_CURPOS 0x24 #define WC_SERC 0x2d #define WC_FSCDELAY 0x2f #define WC_USERREG 0xc0 #define WC_CLOCK 0x0 #define WC_LEDTEST 0x1 #define WC_VERSION 0x2 /* Offset between transmit and receive */ #define WC_OFFSET 4 #define BIT_CS (1 << 7) #define BIT_ADDR (0xf << 3) #define BIT_LED1 (1 << 0) #define BIT_LED0 (1 << 1) #define BIT_TEST (1 << 2) #define FLAG_STARTED (1 << 0) #define FLAG_NMF (1 << 1) #define FLAG_SENDINGYELLOW (1 << 2) #define FLAG_FALC12 (1 << 3) #define TYPE_T1 1 /* is a T1 card */ #define TYPE_E1 2 /* is an E1 card */ static int chanmap_t1[] = { 2,1,0, 6,5,4, 10,9,8, 14,13,12, 18,17,16, 22,21,20, 26,25,24, 30,29,28 }; static int chanmap_e1[] = { 2,1,0, 7,6,5,4, 11,10,9,8, 15,14,13,12, 19,18,17,16, 23,22,21,20, 27,26,25,24, 31,30,29,28 }; #ifdef FANCY_ALARM static int altab[] = { 0, 0, 0, 1, 2, 3, 4, 6, 8, 9, 11, 13, 16, 18, 20, 22, 24, 25, 27, 28, 29, 30, 31, 31, 32, 31, 31, 30, 29, 28, 27, 25, 23, 22, 20, 18, 16, 13, 11, 9, 8, 6, 4, 3, 2, 1, 0, 0, }; #endif struct t1 { struct pci_dev *dev; spinlock_t lock; int spantype; int spanflags; /* Span flags */ unsigned char txsigs[16]; /* Copy of tx sig registers */ int num; int alarmcount; /* How much red alarm we've seen */ int alarmdebounce; /* Our offset for finding channel 1 */ int offset; char *variety; unsigned int intcount; int usecount; int clocktimeout; int sync; int dead; int blinktimer; int alarmtimer; int checktiming; /* Set >0 to cause the timing source to be checked */ int loopupcnt; int loopdowncnt; int miss; int misslast; int *chanmap; #ifdef FANCY_ALARM int alarmpos; #endif unsigned char ledtestreg; unsigned char outbyte; unsigned long ioaddr; unsigned short canary; /* T1 signalling */ dma_addr_t readdma; dma_addr_t writedma; volatile unsigned char *writechunk; /* Double-word aligned write memory */ volatile unsigned char *readchunk; /* Double-word aligned read memory */ unsigned char ec_chunk1[31][ZT_CHUNKSIZE]; unsigned char ec_chunk2[31][ZT_CHUNKSIZE]; unsigned char tempo[32]; struct zt_span span; /* Span */ struct zt_chan chans[31]; /* Channels */ }; #define CANARY 0xca1e static int debug = 0; /* doesnt do anything */ static int alarmdebounce = 0; static int loopback = 0; static int clockextra = 0; static int t1e1override = -1; static struct t1 *cards[WC_MAX_CARDS]; static inline void start_alarm(struct t1 *wc) { #ifdef FANCY_ALARM wc->alarmpos = 0; #endif wc->blinktimer = 0; } static inline void stop_alarm(struct t1 *wc) { #ifdef FANCY_ALARM wc->alarmpos = 0; #endif wc->blinktimer = 0; } static inline void __select_framer(struct t1 *wc, int reg) { /* Top four bits of address from AUX 6-3 */ wc->outbyte &= ~BIT_CS; wc->outbyte &= ~BIT_ADDR; wc->outbyte |= (reg & 0xf0) >> 1; outb(wc->outbyte, wc->ioaddr + WC_AUXD); } static inline void __select_control(struct t1 *wc) { if (!(wc->outbyte & BIT_CS)) { wc->outbyte |= BIT_CS; outb(wc->outbyte, wc->ioaddr + WC_AUXD); } } static int t1xxp_open(struct zt_chan *chan) { struct t1 *wc = chan->pvt; if (wc->dead) return -ENODEV; wc->usecount++; #ifndef LINUX26 MOD_INC_USE_COUNT; #else try_module_get(THIS_MODULE); #endif return 0; } static int __control_set_reg(struct t1 *wc, int reg, unsigned char val) { __select_control(wc); outb(val, wc->ioaddr + WC_USERREG + ((reg & 0xf) << 2)); return 0; } static int control_set_reg(struct t1 *wc, int reg, unsigned char val) { unsigned long flags; int res; spin_lock_irqsave(&wc->lock, flags); res = __control_set_reg(wc, reg, val); spin_unlock_irqrestore(&wc->lock, flags); return res; } static int __control_get_reg(struct t1 *wc, int reg) { unsigned char res; /* The following makes UTTERLY no sense, but what was happening was that reads in some cases were not actually happening on the physical bus. Why, we dunno. But in debugging, we found that writing before reading (in this case to an unused position) seems to get rid of the problem */ __control_set_reg(wc,3,0x69); /* do magic here */ /* now get the read byte from the Xilinx part */ res = inb(wc->ioaddr + WC_USERREG + ((reg & 0xf) << 2)); return res; } static int control_get_reg(struct t1 *wc, int reg) { unsigned long flags; int res; spin_lock_irqsave(&wc->lock, flags); res = __control_get_reg(wc, reg); spin_unlock_irqrestore(&wc->lock, flags); return res; } static inline unsigned int __t1_framer_in(struct t1 *wc, const unsigned int reg) { unsigned char res; __select_framer(wc, reg); /* Get value */ res = inb(wc->ioaddr + WC_USERREG + ((reg & 0xf) << 2)); return res; #if 0 unsigned int ret; __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff)); __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff) | ( 1 << 10) | WC_LREAD); ret = __t1_pci_in(wc, WC_LDATA); __t1_pci_out(wc, WC_LADDR, 0); return ret & 0xff; #endif } static inline unsigned int t1_framer_in(struct t1 *wc, const unsigned int addr) { unsigned long flags; unsigned int ret; spin_lock_irqsave(&wc->lock, flags); ret = __t1_framer_in(wc, addr); spin_unlock_irqrestore(&wc->lock, flags); return ret; } static inline void __t1_framer_out(struct t1 *wc, const unsigned int reg, const unsigned int val) { if (debug > 1) printk("Writing %02x to address %02x\n", val, reg); __select_framer(wc, reg); /* Send address */ outb(val, wc->ioaddr + WC_USERREG + ((reg & 0xf) << 2)); #if 0 __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff)); __t1_pci_out(wc, WC_LDATA, value); __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff) | (1 << 10)); __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff) | (1 << 10) | WC_LWRITE); __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff) | (1 << 10)); __t1_pci_out(wc, WC_LADDR, (unit << 8) | (addr & 0xff)); __t1_pci_out(wc, WC_LADDR, 0); if (debug) printk("Write complete\n"); #endif #if 0 { unsigned int tmp; tmp = t1_framer_in(wc, unit, addr); if (tmp != value) { printk("Expected %d from unit %d register %d but got %d instead\n", value, unit, addr, tmp); } } #endif } static inline void t1_framer_out(struct t1 *wc, const unsigned int addr, const unsigned int value) { unsigned long flags; spin_lock_irqsave(&wc->lock, flags); __t1_framer_out(wc, addr, value); spin_unlock_irqrestore(&wc->lock, flags); } static void t1xxp_release(struct t1 *wc) { zt_unregister(&wc->span); kfree(wc); printk("Freed a Wildcard\n"); } static int t1xxp_close(struct zt_chan *chan) { struct t1 *wc = chan->pvt; wc->usecount--; #ifndef LINUX26 MOD_DEC_USE_COUNT; #else module_put(THIS_MODULE); #endif /* If we're dead, release us now */ if (!wc->usecount && wc->dead) t1xxp_release(wc); return 0; } static void t1xxp_enable_interrupts(struct t1 *wc) { /* Clear interrupts */ outb(0xff, wc->ioaddr + WC_INTSTAT); /* Enable interrupts (we care about all of them) */ outb(0x3c /* 0x3f */, wc->ioaddr + WC_MASK0); /* No external interrupts */ outb(0x00, wc->ioaddr + WC_MASK1); if (debug) printk("Enabled interrupts!\n"); } static void t1xxp_start_dma(struct t1 *wc) { /* Reset Master and TDM */ outb(DELAY | 0x0f, wc->ioaddr + WC_CNTL); set_current_state(TASK_INTERRUPTIBLE); schedule_timeout(1); outb(DELAY | 0x01, wc->ioaddr + WC_CNTL); outb(0x01, wc->ioaddr + WC_OPER); if (debug) printk("Started DMA\n"); outb(0x03, wc->ioaddr + WC_OPER); outb(0x01, wc->ioaddr + WC_OPER); } static void __t1xxp_stop_dma(struct t1 *wc) { outb(0x00, wc->ioaddr + WC_OPER); } static void __t1xxp_disable_interrupts(struct t1 *wc) { outb(0x00, wc->ioaddr + WC_MASK0); outb(0x00, wc->ioaddr + WC_MASK1); } static void __t1xxp_set_clear(struct t1 *wc) { int i,j; unsigned short val=0; for (i=0;i<24;i++) { j = (i/8); if (wc->span.chans[i].flags & ZT_FLAG_CLEAR) val |= 1 << (7 - (i % 8)); if ((i % 8)==7) { if (debug > 1) printk("Putting %d in register %02x\n", val, 0x2f + j); __t1_framer_out(wc, 0x2f + j, val); val = 0; } } } static int t1xxp_ioctl(struct zt_chan *chan, unsigned int cmd, unsigned long data) { struct t4_regs regs; int x; struct t1 *wc; switch(cmd) { case WCT4_GET_REGS: wc = chan->pvt; for (x=0;xioaddr + (x << 2))) | (inb(wc->ioaddr + (x << 2) + 1) << 8) | (inb(wc->ioaddr + (x << 2) + 2) << 16) | (inb(wc->ioaddr + (x << 2) + 3) << 24); #else regs.pci[x] = (inb(wc->ioaddr + x)); #endif for (x=0;xpvt; if (wc->spantype == TYPE_E1) { switch(cmd) { case ZT_MAINT_NONE: printk("XXX Turn off local and remote loops E1 XXX\n"); break; case ZT_MAINT_LOCALLOOP: printk("XXX Turn on local loopback E1 XXX\n"); break; case ZT_MAINT_REMOTELOOP: printk("XXX Turn on remote loopback E1 XXX\n"); break; case ZT_MAINT_LOOPUP: printk("XXX Send loopup code E1 XXX\n"); break; case ZT_MAINT_LOOPDOWN: printk("XXX Send loopdown code E1 XXX\n"); break; case ZT_MAINT_LOOPSTOP: printk("XXX Stop sending loop codes E1 XXX\n"); break; default: printk("TE110P: Unknown E1 maint command: %d\n", cmd); break; } } else { switch(cmd) { case ZT_MAINT_NONE: printk("XXX Turn off local and remote loops T1 XXX\n"); break; case ZT_MAINT_LOCALLOOP: printk("XXX Turn on local loop and no remote loop XXX\n"); break; case ZT_MAINT_REMOTELOOP: printk("XXX Turn on remote loopup XXX\n"); break; case ZT_MAINT_LOOPUP: t1_framer_out(wc, 0x21, 0x50); /* FMR5: Nothing but RBS mode */ break; case ZT_MAINT_LOOPDOWN: t1_framer_out(wc, 0x21, 0x60); /* FMR5: Nothing but RBS mode */ break; case ZT_MAINT_LOOPSTOP: t1_framer_out(wc, 0x21, 0x40); /* FMR5: Nothing but RBS mode */ break; default: printk("TE110P: Unknown T1 maint command: %d\n", cmd); break; } } return 0; } static int t1xxp_rbsbits(struct zt_chan *chan, int bits) { u_char m,c; int n,b; struct t1 *wc = chan->pvt; unsigned long flags; if(debug > 1) printk("Setting bits to %d on channel %s\n", bits, chan->name); spin_lock_irqsave(&wc->lock, flags); if (wc->spantype == TYPE_E1) { /* do it E1 way */ if (chan->chanpos == 16) { spin_unlock_irqrestore(&wc->lock, flags); return 0; } n = chan->chanpos - 1; if (chan->chanpos > 15) n--; b = (n % 15); c = wc->txsigs[b]; m = (n / 15) << 2; /* nibble selector */ c &= (0xf << m); /* keep the other nibble */ c |= (bits & 0xf) << (4 - m); /* put our new nibble here */ wc->txsigs[b] = c; /* output them to the chip */ __t1_framer_out(wc,0x71 + b,c); } else if (wc->span.lineconfig & ZT_CONFIG_D4) { n = chan->chanpos - 1; b = (n/4); c = wc->txsigs[b]; m = ((3 - (n % 4)) << 1); /* nibble selector */ c &= ~(0x3 << m); /* keep the other nibble */ c |= ((bits >> 2) & 0x3) << m; /* put our new nibble here */ wc->txsigs[b] = c; /* output them to the chip */ __t1_framer_out(wc,0x70 + b,c); __t1_framer_out(wc,0x70 + b + 6,c); } else if (wc->span.lineconfig & ZT_CONFIG_ESF) { n = chan->chanpos - 1; b = (n/2); c = wc->txsigs[b]; m = ((n % 2) << 2); /* nibble selector */ c &= (0xf << m); /* keep the other nibble */ c |= (bits & 0xf) << (4 - m); /* put our new nibble here */ wc->txsigs[b] = c; /* output them to the chip */ __t1_framer_out(wc,0x70 + b,c); } spin_unlock_irqrestore(&wc->lock, flags); if (debug > 1) printk("Finished setting RBS bits\n"); return 0; } static void __t1_check_sigbits(struct t1 *wc) { int a,i,rxs; if (!(wc->span.flags & ZT_FLAG_RUNNING)) return; if (wc->spantype == TYPE_E1) { for (i = 0; i < 15; i++) { a = __t1_framer_in(wc, 0x71 + i); /* Get high channel in low bits */ rxs = (a & 0xf); if (!(wc->span.chans[i+16].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i+16].rxsig != rxs) zt_rbsbits(&wc->span.chans[i+16], rxs); } rxs = (a >> 4) & 0xf; if (!(wc->span.chans[i].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i].rxsig != rxs) zt_rbsbits(&wc->span.chans[i], rxs); } } } else if (wc->span.lineconfig & ZT_CONFIG_D4) { for (i = 0; i < 24; i+=4) { a = __t1_framer_in(wc, 0x70 + (i>>2)); /* Get high channel in low bits */ rxs = (a & 0x3) << 2; if (!(wc->span.chans[i+3].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i+3].rxsig != rxs) zt_rbsbits(&wc->span.chans[i+3], rxs); } rxs = (a & 0xc); if (!(wc->span.chans[i+2].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i+2].rxsig != rxs) zt_rbsbits(&wc->span.chans[i+2], rxs); } rxs = (a >> 2) & 0xc; if (!(wc->span.chans[i+1].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i+1].rxsig != rxs) zt_rbsbits(&wc->span.chans[i+1], rxs); } rxs = (a >> 4) & 0xc; if (!(wc->span.chans[i].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i].rxsig != rxs) zt_rbsbits(&wc->span.chans[i], rxs); } } } else { for (i = 0; i < 24; i+=2) { a = __t1_framer_in(wc, 0x70 + (i>>1)); /* Get high channel in low bits */ rxs = (a & 0xf); if (!(wc->span.chans[i+1].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i+1].rxsig != rxs) zt_rbsbits(&wc->span.chans[i+1], rxs); } rxs = (a >> 4) & 0xf; if (!(wc->span.chans[i].sig & ZT_SIG_CLEAR)) { if (wc->span.chans[i].rxsig != rxs) zt_rbsbits(&wc->span.chans[i], rxs); } } } } static void t4_serial_setup(struct t1 *wc) { printk("TE110P: Setting up global serial parameters for %s %s\n", wc->spantype == TYPE_E1 ? "E1" : "T1", wc->spanflags & FLAG_FALC12 ? "FALC V1.2" : "FALC V2.1"); t1_framer_out(wc, 0x85, 0xe0); /* GPC1: Multiplex mode enabled, FSC is output, active low, RCLK from channel 0 */ t1_framer_out(wc, 0x08, 0x05); /* IPC: Interrupt push/pull active low */ if (wc->spanflags & FLAG_FALC12) { t1_framer_out(wc, 0x92, 0x00); t1_framer_out(wc, 0x93, 0x58); t1_framer_out(wc, 0x94, 0xd2); t1_framer_out(wc, 0x95, 0xc2); t1_framer_out(wc, 0x96, 0x03); t1_framer_out(wc, 0x97, 0x10); } else { #ifdef TRUST_INFINEON_ERRATA if (wc->spantype == TYPE_E1) { /* Global clocks (8.192 Mhz CLK) */ t1_framer_out(wc, 0x92, 0x00); t1_framer_out(wc, 0x93, 0x00); t1_framer_out(wc, 0x94, 0x00); t1_framer_out(wc, 0x95, 0x00); t1_framer_out(wc, 0x96, 0x00); t1_framer_out(wc, 0x97, 0x0F); t1_framer_out(wc, 0x98, 0x80); t1_framer_out(wc, 0x99, 0x00); } else { /* Global clocks (8.192 Mhz CLK) */ t1_framer_out(wc, 0x92, 0x00); t1_framer_out(wc, 0x93, 0x10); t1_framer_out(wc, 0x94, 0xfb); t1_framer_out(wc, 0x95, 0x03); t1_framer_out(wc, 0x96, 0x00); t1_framer_out(wc, 0x97, 0x0b); t1_framer_out(wc, 0x98, 0x8c); t1_framer_out(wc, 0x99, 0x80); } #else t1_framer_out(wc, 0x92, 0x66); t1_framer_out(wc, 0x93, 0x0e); t1_framer_out(wc, 0x94, 0x3f); t1_framer_out(wc, 0x95, 0x0f); t1_framer_out(wc, 0x96, 0x04); t1_framer_out(wc, 0x97, 0x3c); t1_framer_out(wc, 0x98, 0x9c); t1_framer_out(wc, 0x99, 0x90); #endif } /* Configure interrupts */ t1_framer_out(wc, 0x46, 0x40); /* GCR: Interrupt on Activation/Deactivation of AIX, LOS */ /* Configure system interface */ t1_framer_out(wc, 0x3e, 0x02); /* SIC1: 4.096 Mhz clock/bus, double buffer receive / transmit, byte interleaved */ t1_framer_out(wc, 0x3f, 0x00); /* SIC2: No FFS, no center receive eliastic buffer, phase 0 */ t1_framer_out(wc, 0x40, 0x04); /* SIC3: Edges for capture */ t1_framer_out(wc, 0x44, 0x30); /* CMR1: RCLK is at 8.192 Mhz dejittered */ t1_framer_out(wc, 0x45, 0x00); /* CMR2: We provide sync and clock for tx and rx. */ t1_framer_out(wc, 0x22, 0x00); /* XC0: Normal operation of Sa-bits */ t1_framer_out(wc, 0x23, 0x04); /* XC1: 0 offset */ t1_framer_out(wc, 0x24, 0x07); /* RC0: Just shy of 255 */ if (wc->spanflags & FLAG_FALC12) t1_framer_out(wc, 0x25, 0x04); /* RC1: The rest of RC0 */ else t1_framer_out(wc, 0x25, 0x06); /* RC1: The rest of RC0 */ /* Configure ports */ t1_framer_out(wc, 0x80, 0x00); /* PC1: SPYR/SPYX input on RPA/XPA */ t1_framer_out(wc, 0x81, 0x22); /* PC2: RMFB/XSIG output/input on RPB/XPB */ t1_framer_out(wc, 0x82, 0x65); /* PC3: Some unused stuff */ t1_framer_out(wc, 0x83, 0x35); /* PC4: Some more unused stuff */ t1_framer_out(wc, 0x84, 0x31); /* PC5: XMFS active low, SCLKR is input, RCLK is output */ t1_framer_out(wc, 0x86, 0x03); /* PC6: CLK1 is Tx Clock output, CLK2 is 8.192 Mhz from DCO-R */ t1_framer_out(wc, 0x3b, 0x00); /* Clear LCR1 */ printk("TE110P: Successfully initialized serial bus for card\n"); } static void __t1_configure_t1(struct t1 *wc, int lineconfig, int txlevel) { unsigned int fmr4, fmr2, fmr1, fmr0, lim2; char *framing, *line; int mytxlevel; if ((txlevel > 7) || (txlevel < 4)) mytxlevel = 0; else mytxlevel = txlevel - 4; fmr1 = 0x1c; /* FMR1: Mode 0, T1 mode, CRC on for ESF, 2.048 Mhz system data rate, no XAIS */ fmr2 = 0x22; /* FMR2: no payload loopback, auto send yellow alarm */ if (loopback) fmr2 |= 0x4; fmr4 = 0x0c; /* FMR4: Lose sync on 2 out of 5 framing bits, auto resync */ lim2 = 0x21; /* LIM2: 50% peak is a "1", Advanced Loss recovery */ lim2 |= (mytxlevel << 6); /* LIM2: Add line buildout */ __t1_framer_out(wc, 0x1d, fmr1); __t1_framer_out(wc, 0x1e, fmr2); /* Configure line interface */ if (lineconfig & ZT_CONFIG_AMI) { line = "AMI"; fmr0 = 0xa0; } else { line = "B8ZS"; fmr0 = 0xf0; } if (lineconfig & ZT_CONFIG_D4) { framing = "D4"; } else { framing = "ESF"; fmr4 |= 0x2; fmr2 |= 0xc0; } __t1_framer_out(wc, 0x1c, fmr0); __t1_framer_out(wc, 0x20, fmr4); __t1_framer_out(wc, 0x21, 0x40); /* FMR5: Enable RBS mode */ __t1_framer_out(wc, 0x37, 0xf8); /* LIM1: Clear data in case of LOS, Set receiver threshold (0.5V), No remote loop, no DRS */ __t1_framer_out(wc, 0x36, 0x08); /* LIM0: Enable auto long haul mode, no local loop (must be after LIM1) */ __t1_framer_out(wc, 0x02, 0x50); /* CMDR: Reset the receiver and transmitter line interface */ __t1_framer_out(wc, 0x02, 0x00); /* CMDR: Reset the receiver and transmitter line interface */ __t1_framer_out(wc, 0x3a, lim2); /* LIM2: 50% peak amplitude is a "1" */ __t1_framer_out(wc, 0x38, 0x0a); /* PCD: LOS after 176 consecutive "zeros" */ __t1_framer_out(wc, 0x39, 0x15); /* PCR: 22 "ones" clear LOS */ /* Generate pulse mask for T1 */ switch(mytxlevel) { case 3: __t1_framer_out(wc, 0x26, 0x07); /* XPM0 */ __t1_framer_out(wc, 0x27, 0x01); /* XPM1 */ __t1_framer_out(wc, 0x28, 0x00); /* XPM2 */ break; case 2: __t1_framer_out(wc, 0x26, 0x8c); /* XPM0 */ __t1_framer_out(wc, 0x27, 0x11); /* XPM1 */ __t1_framer_out(wc, 0x28, 0x01); /* XPM2 */ break; case 1: __t1_framer_out(wc, 0x26, 0x8c); /* XPM0 */ __t1_framer_out(wc, 0x27, 0x01); /* XPM1 */ __t1_framer_out(wc, 0x28, 0x00); /* XPM2 */ break; case 0: default: __t1_framer_out(wc, 0x26, 0xd7); /* XPM0 */ __t1_framer_out(wc, 0x27, 0x22); /* XPM1 */ __t1_framer_out(wc, 0x28, 0x01); /* XPM2 */ break; } printk("TE110P: Span configured for %s/%s\n", framing, line); } static void __t1_configure_e1(struct t1 *wc, int lineconfig) { unsigned int fmr2, fmr1, fmr0; unsigned int cas = 0; char *crc4 = ""; char *framing, *line; fmr1 = 0x44; /* FMR1: E1 mode, Automatic force resync, PCM30 mode, 8.192 Mhz backplane, no XAIS */ fmr2 = 0x03; /* FMR2: Auto transmit remote alarm, auto loss of multiframe recovery, no payload loopback */ if (loopback) fmr2 |= 0x4; if (lineconfig & ZT_CONFIG_CRC4) { fmr1 |= 0x08; /* CRC4 transmit */ fmr2 |= 0xc0; /* CRC4 receive */ crc4 = "/CRC4"; } __t1_framer_out(wc, 0x1d, fmr1); __t1_framer_out(wc, 0x1e, fmr2); /* Configure line interface */ if (lineconfig & ZT_CONFIG_AMI) { line = "AMI"; fmr0 = 0xa0; } else { line = "HDB3"; fmr0 = 0xf0; } if (lineconfig & ZT_CONFIG_CCS) { framing = "CCS"; } else { framing = "CAS"; cas = 0x40; } __t1_framer_out(wc, 0x1c, fmr0); __t1_framer_out(wc, 0x37, 0xf0 /*| 0x6 */ ); /* LIM1: Clear data in case of LOS, Set receiver threshold (0.5V), No remote loop, no DRS */ __t1_framer_out(wc, 0x36, 0x08); /* LIM0: Enable auto long haul mode, no local loop (must be after LIM1) */ __t1_framer_out(wc, 0x02, 0x50); /* CMDR: Reset the receiver and transmitter line interface */ __t1_framer_out(wc, 0x02, 0x00); /* CMDR: Reset the receiver and transmitter line interface */ /* Condition receive line interface for E1 after reset */ __t1_framer_out(wc, 0xbb, 0x17); __t1_framer_out(wc, 0xbc, 0x55); __t1_framer_out(wc, 0xbb, 0x97); __t1_framer_out(wc, 0xbb, 0x11); __t1_framer_out(wc, 0xbc, 0xaa); __t1_framer_out(wc, 0xbb, 0x91); __t1_framer_out(wc, 0xbb, 0x12); __t1_framer_out(wc, 0xbc, 0x55); __t1_framer_out(wc, 0xbb, 0x92); __t1_framer_out(wc, 0xbb, 0x0c); __t1_framer_out(wc, 0xbb, 0x00); __t1_framer_out(wc, 0xbb, 0x8c); __t1_framer_out(wc, 0x3a, 0x20); /* LIM2: 50% peak amplitude is a "1" */ __t1_framer_out(wc, 0x38, 0x0a); /* PCD: LOS after 176 consecutive "zeros" */ __t1_framer_out(wc, 0x39, 0x15); /* PCR: 22 "ones" clear LOS */ __t1_framer_out(wc, 0x20, 0x9f); /* XSW: Spare bits all to 1 */ __t1_framer_out(wc, 0x21, 0x1c|cas); /* XSP: E-bit set when async. AXS auto, XSIF to 1 */ /* Generate pulse mask for E1 */ __t1_framer_out(wc, 0x26, 0x54); /* XPM0 */ __t1_framer_out(wc, 0x27, 0x02); /* XPM1 */ __t1_framer_out(wc, 0x28, 0x00); /* XPM2 */ printk("TE110P: Span configured for %s/%s%s\n", framing, line, crc4); } static void t1xxp_framer_start(struct t1 *wc, struct zt_span *span) { int alreadyrunning = wc->span.flags & ZT_FLAG_RUNNING; unsigned long flags; spin_lock_irqsave(&wc->lock, flags); if (wc->spantype == TYPE_E1) { /* if this is an E1 card */ __t1_configure_e1(wc, span->lineconfig); } else { /* is a T1 card */ __t1_configure_t1(wc, span->lineconfig, span->txlevel); __t1xxp_set_clear(wc); } if (!alreadyrunning) wc->span.flags |= ZT_FLAG_RUNNING; spin_unlock_irqrestore(&wc->lock, flags); } static int t1xxp_startup(struct zt_span *span) { struct t1 *wc = span->pvt; int i,alreadyrunning = span->flags & ZT_FLAG_RUNNING; /* initialize the start value for the entire chunk of last ec buffer */ for(i = 0; i < span->channels; i++) { memset(wc->ec_chunk1[i], ZT_LIN2X(0,&span->chans[i]),ZT_CHUNKSIZE); memset(wc->ec_chunk2[i], ZT_LIN2X(0,&span->chans[i]),ZT_CHUNKSIZE); } /* Reset framer with proper parameters and start */ t1xxp_framer_start(wc, span); printk("Calling startup (flags is %d)\n", span->flags); if (!alreadyrunning) { /* Only if we're not already going */ t1xxp_enable_interrupts(wc); t1xxp_start_dma(wc); span->flags |= ZT_FLAG_RUNNING; } return 0; } static int t1xxp_shutdown(struct zt_span *span) { struct t1 *wc = span->pvt; unsigned long flags; spin_lock_irqsave(&wc->lock, flags); t1_framer_out(wc, 0x46, 0x41); /* GCR: Interrupt on Activation/Deactivation of AIX, LOS */ __t1xxp_stop_dma(wc); __t1xxp_disable_interrupts(wc); span->flags &= ~ZT_FLAG_RUNNING; spin_unlock_irqrestore(&wc->lock, flags); return 0; } static int t1xxp_chanconfig(struct zt_chan *chan, int sigtype) { struct t1 *wc = chan->pvt; unsigned long flags; int alreadyrunning = chan->span->flags & ZT_FLAG_RUNNING; spin_lock_irqsave(&wc->lock, flags); if (alreadyrunning && (wc->spantype != TYPE_E1)) __t1xxp_set_clear(wc); spin_unlock_irqrestore(&wc->lock, flags); return 0; } static int t1xxp_spanconfig(struct zt_span *span, struct zt_lineconfig *lc) { struct t1 *wc = span->pvt; span->lineconfig = lc->lineconfig; span->txlevel = lc->lbo; span->rxlevel = 0; /* Do we want to SYNC on receive or not */ wc->sync = lc->sync; /* If already running, apply changes immediately */ if (span->flags & ZT_FLAG_RUNNING) return t1xxp_startup(span); return 0; } static int t1xxp_software_init(struct t1 *wc) { int x; /* Find position */ for (x=0;x= WC_MAX_CARDS) return -1; t4_serial_setup(wc); wc->num = x; sprintf(wc->span.name, "WCT1/%d", wc->num); sprintf(wc->span.desc, "%s Card %d", wc->variety, wc->num); wc->span.spanconfig = t1xxp_spanconfig; wc->span.chanconfig = t1xxp_chanconfig; wc->span.startup = t1xxp_startup; wc->span.shutdown = t1xxp_shutdown; wc->span.rbsbits = t1xxp_rbsbits; wc->span.maint = t1xxp_maint; wc->span.open = t1xxp_open; wc->span.close = t1xxp_close; if (wc->spantype == TYPE_E1) wc->span.channels = 31; else wc->span.channels = 24; wc->span.chans = wc->chans; wc->span.flags = ZT_FLAG_RBS; wc->span.linecompat = ZT_CONFIG_AMI | ZT_CONFIG_B8ZS | ZT_CONFIG_D4 | ZT_CONFIG_ESF; wc->span.ioctl = t1xxp_ioctl; wc->span.pvt = wc; if (wc->spantype == TYPE_E1) wc->span.deflaw = ZT_LAW_ALAW; else wc->span.deflaw = ZT_LAW_MULAW; init_waitqueue_head(&wc->span.maintq); for (x=0;xspan.channels;x++) { sprintf(wc->chans[x].name, "WCT1/%d/%d", wc->num, x + 1); wc->chans[x].sigcap = ZT_SIG_EM | ZT_SIG_CLEAR | ZT_SIG_EM_E1 | ZT_SIG_FXSLS | ZT_SIG_FXSGS | ZT_SIG_FXSKS | ZT_SIG_FXOLS | ZT_SIG_DACS_RBS | ZT_SIG_FXOGS | ZT_SIG_FXOKS | ZT_SIG_CAS | ZT_SIG_SF; wc->chans[x].pvt = wc; wc->chans[x].chanpos = x + 1; } if (zt_register(&wc->span, 0)) { printk("Unable to register span with zaptel\n"); return -1; } return 0; } static inline void __handle_leds(struct t1 *wc) { int oldreg; if (wc->span.alarms & (ZT_ALARM_RED | ZT_ALARM_BLUE)) { /* Red/Blue alarm */ wc->blinktimer++; #ifdef FANCY_ALARM if (wc->blinktimer == (altab[wc->alarmpos] >> 1)) { wc->ledtestreg = (wc->ledtestreg | BIT_LED1) & ~BIT_LED0; __control_set_reg(wc, WC_LEDTEST, wc->ledtestreg); } if (wc->blinktimer >= 0xf) { wc->ledtestreg = wc->ledtestreg & ~(BIT_LED0 | BIT_LED1); __control_set_reg(wc, WC_LEDTEST, wc->ledtestreg); wc->blinktimer = -1; wc->alarmpos++; if (wc->alarmpos >= (sizeof(altab) / sizeof(altab[0]))) wc->alarmpos = 0; } #else if (wc->blinktimer == 160) { wc->ledtestreg = (wc->ledtestreg | BIT_LED1) & ~BIT_LED0; __control_set_reg(wc, WC_LEDTEST, wc->ledtestreg); } else if (wc->blinktimer == 480) { wc->ledtestreg = wc->ledtestreg & ~(BIT_LED0 | BIT_LED1); __control_set_reg(wc, WC_LEDTEST, wc->ledtestreg); wc->blinktimer = 0; } #endif } else if (wc->span.alarms & ZT_ALARM_YELLOW) { /* Yellow Alarm */ if (!(wc->blinktimer % 2)) wc->ledtestreg = (wc->ledtestreg | BIT_LED1) & ~BIT_LED0; else wc->ledtestreg = (wc->ledtestreg | BIT_LED0) & ~BIT_LED1; __control_set_reg(wc, WC_LEDTEST, wc->ledtestreg); } else { /* No Alarm */ oldreg = wc->ledtestreg; if (wc->span.maintstat != ZT_MAINT_NONE) wc->ledtestreg |= BIT_TEST; else wc->ledtestreg &= ~BIT_TEST; if (wc->span.flags & ZT_FLAG_RUNNING) wc->ledtestreg = (wc->ledtestreg | BIT_LED0) & ~BIT_LED1; else wc->ledtestreg = wc->ledtestreg & ~(BIT_LED0 | BIT_LED1); if (oldreg != wc->ledtestreg) __control_set_reg(wc, WC_LEDTEST, wc->ledtestreg); } } static void t1xxp_transmitprep(struct t1 *wc, int ints) { volatile unsigned char *txbuf; int x,y; int pos; if (ints & 0x04 /* 0x01 */) { /* We just finished sending the first buffer, start filling it now */ txbuf = wc->writechunk; } else { /* Just finished sending second buffer, fill it now */ txbuf = wc->writechunk + 32 * ZT_CHUNKSIZE; } zt_transmit(&wc->span); for (x=0;xoffset;x++) txbuf[x] = wc->tempo[x]; for (y=0;yspan.channels;x++) { pos = y * 32 + wc->chanmap[x] + wc->offset; /* Put channel number as outgoing data */ if (pos < 32 * ZT_CHUNKSIZE) txbuf[pos] = wc->chans[x].writechunk[y]; else wc->tempo[pos - 32 * ZT_CHUNKSIZE] = wc->chans[x].writechunk[y]; } } } static void t1xxp_receiveprep(struct t1 *wc, int ints) { volatile unsigned char *rxbuf; volatile unsigned int *canary; int x; int y; unsigned int oldcan; if (ints & 0x04) { /* Just received first buffer */ rxbuf = wc->readchunk; canary = (unsigned int *)(wc->readchunk + ZT_CHUNKSIZE * 64 - 4); } else { rxbuf = wc->readchunk + ZT_CHUNKSIZE * 32; canary = (unsigned int *)(wc->readchunk + ZT_CHUNKSIZE * 32 - 4); } oldcan = *canary; if (((oldcan & 0xffff0000) >> 16) != CANARY) { /* Check top part */ if (debug) printk("Expecting top %04x, got %04x\n", CANARY, (oldcan & 0xffff0000) >> 16); wc->span.irqmisses++; } else if ((oldcan & 0xffff) != ((wc->canary - 1) & 0xffff)) { if (debug) printk("Expecting bottom %d, got %d\n", wc->canary - 1, oldcan & 0xffff); wc->span.irqmisses++; } for (y=0;yspan.channels;x++) { /* XXX Optimize, remove * and + XXX */ /* Must map received channels into appropriate data */ wc->chans[x].readchunk[y] = rxbuf[32 * y + ((wc->chanmap[x] + WC_OFFSET + wc->offset) & 0x1f)]; } if (wc->spantype != TYPE_E1) { for (x=3;x<32;x+=4) { if (rxbuf[32 * y + ((x + WC_OFFSET) & 0x1f)] == 0x7f) { if (wc->offset != (x-3)) { /* Resync */ control_set_reg(wc, WC_CLOCK, 0x06 | wc->sync | clockextra); wc->clocktimeout = 100; #if 1 if (debug) printk("T1: Lost our place, resyncing\n"); #endif } } } } else { if (!wc->clocktimeout && !wc->span.alarms) { if ((rxbuf[32 * y + ((3 + WC_OFFSET + wc->offset) & 0x1f)] & 0x7f) != 0x1b) { if (wc->miss) { if (debug) printk("Double miss (%d, %d)...\n", wc->misslast, rxbuf[32 * y + ((3 + WC_OFFSET + wc->offset) & 0x1f)]); control_set_reg(wc, WC_CLOCK, 0x06 | wc->sync | clockextra); wc->clocktimeout = 100; } else { wc->miss = 1; wc->misslast = rxbuf[32 * y + ((3 + WC_OFFSET + wc->offset) & 0x1f)]; } } else { wc->miss = 0; } } else { wc->miss = 0; } } } /* Store the next canary */ canary = (unsigned int *)(rxbuf + ZT_CHUNKSIZE * 32 - 4); *canary = (wc->canary++) | (CANARY << 16); for (x=0;xspan.channels;x++) { zt_ec_chunk(&wc->chans[x], wc->chans[x].readchunk, wc->ec_chunk2[x]); memcpy(wc->ec_chunk2[x],wc->ec_chunk1[x],ZT_CHUNKSIZE); memcpy(wc->ec_chunk1[x],wc->chans[x].writechunk,ZT_CHUNKSIZE); } zt_receive(&wc->span); } static void __t1_check_alarms(struct t1 *wc) { unsigned char c,d; int alarms; int x,j; if (!(wc->span.flags & ZT_FLAG_RUNNING)) return; c = __t1_framer_in(wc, 0x4c); if (wc->spanflags & FLAG_FALC12) d = __t1_framer_in(wc, 0x4f); else d = __t1_framer_in(wc, 0x4d); /* Assume no alarms */ alarms = 0; /* And consider only carrier alarms */ wc->span.alarms &= (ZT_ALARM_RED | ZT_ALARM_BLUE | ZT_ALARM_NOTOPEN); if (wc->spantype == TYPE_E1) { if (c & 0x04) { /* No multiframe found, force RAI high after 400ms only if we haven't found a multiframe since last loss of frame */ if (!(wc->spanflags & FLAG_NMF)) { __t1_framer_out(wc, 0x20, 0x9f | 0x20); /* LIM0: Force RAI High */ wc->spanflags |= FLAG_NMF; printk("NMF workaround on!\n"); } __t1_framer_out(wc, 0x1e, 0xc3); /* Reset to CRC4 mode */ __t1_framer_out(wc, 0x1c, 0xf2); /* Force Resync */ __t1_framer_out(wc, 0x1c, 0xf0); /* Force Resync */ } else if (!(c & 0x02)) { if ((wc->spanflags & FLAG_NMF)) { __t1_framer_out(wc, 0x20, 0x9f); /* LIM0: Clear forced RAI */ wc->spanflags &= ~FLAG_NMF; printk("NMF workaround off!\n"); } } } else { /* Detect loopup code if we're not sending one */ if ((!wc->span.mainttimer) && (d & 0x08)) { /* Loop-up code detected */ if ((wc->loopupcnt++ > 80) && (wc->span.maintstat != ZT_MAINT_REMOTELOOP)) { __t1_framer_out(wc, 0x36, 0x08); /* LIM0: Disable any local loop */ __t1_framer_out(wc, 0x37, 0xf6 ); /* LIM1: Enable remote loop */ wc->span.maintstat = ZT_MAINT_REMOTELOOP; } } else wc->loopupcnt = 0; /* Same for loopdown code */ if ((!wc->span.mainttimer) && (d & 0x10)) { /* Loop-down code detected */ if ((wc->loopdowncnt++ > 80) && (wc->span.maintstat == ZT_MAINT_REMOTELOOP)) { __t1_framer_out(wc, 0x36, 0x08); /* LIM0: Disable any local loop */ __t1_framer_out(wc, 0x37, 0xf0 ); /* LIM1: Disable remote loop */ wc->span.maintstat = ZT_MAINT_NONE; } } else wc->loopdowncnt = 0; } if (wc->span.lineconfig & ZT_CONFIG_NOTOPEN) { for (x=0,j=0;x < wc->span.channels;x++) if ((wc->span.chans[x].flags & ZT_FLAG_OPEN) || (wc->span.chans[x].flags & ZT_FLAG_NETDEV)) j++; if (!j) alarms |= ZT_ALARM_NOTOPEN; } if (c & 0xa0) { if (wc->alarmcount >= alarmdebounce) alarms |= ZT_ALARM_RED; else wc->alarmcount++; } else wc->alarmcount = 0; if (c & 0x4) alarms |= ZT_ALARM_BLUE; if (((!wc->span.alarms) && alarms) || (wc->span.alarms && (!alarms))) wc->checktiming = 1; /* Keep track of recovering */ if ((!alarms) && wc->span.alarms) wc->alarmtimer = ZT_ALARMSETTLE_TIME; if (wc->alarmtimer) alarms |= ZT_ALARM_RECOVER; /* If receiving alarms, go into Yellow alarm state */ if (alarms && !(wc->spanflags & FLAG_SENDINGYELLOW)) { unsigned char fmr4; #if 1 printk("wcte1xxp: Setting yellow alarm\n"); #endif /* We manually do yellow alarm to handle RECOVER and NOTOPEN, otherwise it's auto anyway */ fmr4 = __t1_framer_in(wc, 0x20); __t1_framer_out(wc, 0x20, fmr4 | 0x20); wc->spanflags |= FLAG_SENDINGYELLOW; } else if ((!alarms) && (wc->spanflags & FLAG_SENDINGYELLOW)) { unsigned char fmr4; #if 1 printk("wcte1xxp: Clearing yellow alarm\n"); #endif /* We manually do yellow alarm to handle RECOVER */ fmr4 = __t1_framer_in(wc, 0x20); __t1_framer_out(wc, 0x20, fmr4 & ~0x20); wc->spanflags &= ~FLAG_SENDINGYELLOW; } /* Re-check the timing source when we enter/leave alarm, not withstanding yellow alarm */ if (c & 0x10) alarms |= ZT_ALARM_YELLOW; if (wc->span.mainttimer || wc->span.maintstat) alarms |= ZT_ALARM_LOOPBACK; wc->span.alarms = alarms; zt_alarm_notify(&wc->span); } static void __t1_do_counters(struct t1 *wc) { if (wc->alarmtimer) { if (!--wc->alarmtimer) { wc->span.alarms &= ~(ZT_ALARM_RECOVER); zt_alarm_notify(&wc->span); } } } #ifdef LINUX26 static irqreturn_t t1xxp_interrupt(int irq, void *dev_id, struct pt_regs *regs) #else static void t1xxp_interrupt(int irq, void *dev_id, struct pt_regs *regs) #endif { struct t1 *wc = dev_id; unsigned char ints; unsigned long flags; int x; ints = inb(wc->ioaddr + WC_INTSTAT); outb(ints, wc->ioaddr + WC_INTSTAT); if (!ints) #ifdef LINUX26 return IRQ_NONE; #else return; #endif if (!wc->intcount) { if (debug) printk("Got interrupt: 0x%04x\n", ints); } wc->intcount++; if (wc->clocktimeout && !--wc->clocktimeout) control_set_reg(wc, WC_CLOCK, 0x04 | wc->sync | clockextra); if (ints & 0x0f) { t1xxp_receiveprep(wc, ints); t1xxp_transmitprep(wc, ints); } spin_lock_irqsave(&wc->lock, flags); #if 1 __handle_leds(wc); #endif /* Count down timers */ __t1_do_counters(wc); /* Do some things that we don't have to do very often */ x = wc->intcount & 15 /* 63 */; switch(x) { case 0: case 1: break; case 2: __t1_check_sigbits(wc); break; case 4: /* Check alarms 1/4 as frequently */ if (!(wc->intcount & 0x30)) __t1_check_alarms(wc); break; } spin_unlock_irqrestore(&wc->lock, flags); if (ints & 0x10) printk("PCI Master abort\n"); if (ints & 0x20) printk("PCI Target abort\n"); #ifdef LINUX26 return IRQ_RETVAL(1); #endif } static int t1xxp_hardware_init(struct t1 *wc) { unsigned int falcver; unsigned int x; /* Hardware PCI stuff */ /* Reset chip and registers */ outb(DELAY | 0x0e, wc->ioaddr + WC_CNTL); /* Set all outputs to 0 */ outb(0x00, wc->ioaddr + WC_AUXD); /* Set all to outputs except AUX1 (TDO). */ outb(0xfd, wc->ioaddr + WC_AUXC); /* Configure the serial port: double clock, 20ns width, no inversion, MSB first */ outb(0xc8, wc->ioaddr + WC_SERC); /* Internally delay FSC by one */ outb(0x01, wc->ioaddr + WC_FSCDELAY); /* Back to normal, with automatic DMA wrap around */ outb(DELAY | 0x01, wc->ioaddr + WC_CNTL); /* Make sure serial port and DMA are out of reset */ outb(inb(wc->ioaddr + WC_CNTL) & 0xf9, WC_CNTL); /* Setup DMA Addresses */ /* Start at writedma */ outl(wc->writedma, wc->ioaddr + WC_DMAWS); /* Write start */ /* First frame */ outl(wc->writedma + ZT_CHUNKSIZE * 32 - 4, wc->ioaddr + WC_DMAWI); /* Middle (interrupt) */ /* Second frame */ outl(wc->writedma + ZT_CHUNKSIZE * 32 * 2 - 4, wc->ioaddr + WC_DMAWE); /* End */ outl(wc->readdma, wc->ioaddr + WC_DMARS); /* Read start */ /* First frame */ outl(wc->readdma + ZT_CHUNKSIZE * 32 - 4, wc->ioaddr + WC_DMARI); /* Middle (interrupt) */ /* Second frame */ outl(wc->readdma + ZT_CHUNKSIZE * 32 * 2 - 4, wc->ioaddr + WC_DMARE); /* End */ if (debug) printk("Setting up DMA (write/read = %08lx/%08lx)\n", (long)wc->writedma, (long)wc->readdma); if (t1e1override > -1) { if (t1e1override) wc->spantype = TYPE_E1; else wc->spantype = TYPE_T1; } else { if (control_get_reg(wc, WC_CLOCK) & 0x20) wc->spantype = TYPE_T1; else wc->spantype = TYPE_E1; } /* Check out the controller */ if (debug); printk("Controller version: %02x\n", control_get_reg(wc, WC_VERSION)); control_set_reg(wc, WC_LEDTEST, 0x00); if (wc->spantype == TYPE_E1) wc->chanmap = chanmap_e1; else wc->chanmap = chanmap_t1; /* Setup clock appropriately */ control_set_reg(wc, WC_CLOCK, 0x06 | wc->sync | clockextra); wc->clocktimeout = 100; /* Perform register test on FALC */ for (x=0;x<256;x++) { t1_framer_out(wc, 0x14, x); if ((falcver = t1_framer_in(wc, 0x14)) != x) printk("Wrote '%x' but read '%x'\n", x, falcver); } t1_framer_out(wc, 0x4a, 0xaa); falcver = t1_framer_in(wc ,0x4a); printk("FALC version: %08x\n", falcver); if (!falcver) wc->spanflags |= FLAG_FALC12; start_alarm(wc); return 0; } static int __devinit t1xxp_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int res; struct t1 *wc; unsigned int *canary; if (pci_enable_device(pdev)) { res = -EIO; } else { wc = kmalloc(sizeof(struct t1), GFP_KERNEL); if (wc) { memset(wc, 0x0, sizeof(struct t1)); spin_lock_init(&wc->lock); wc->ioaddr = pci_resource_start(pdev, 0); wc->dev = pdev; wc->offset = 28; /* And you thought 42 was the answer */ wc->writechunk = /* 32 channels, Double-buffer, Read/Write */ (unsigned char *)pci_alloc_consistent(pdev, ZT_MAX_CHUNKSIZE * 32 * 2 * 2, &wc->writedma); if (!wc->writechunk) { printk("wcte11xp: Unable to allocate DMA-able memory\n"); return -ENOMEM; } /* Read is after the whole write piece (in bytes) */ wc->readchunk = wc->writechunk + ZT_CHUNKSIZE * 32 * 2; /* Same thing... */ wc->readdma = wc->writedma + ZT_CHUNKSIZE * 32 * 2; /* Initialize Write/Buffers to all blank data */ memset((void *)wc->writechunk,0x00,ZT_MAX_CHUNKSIZE * 2 * 2 * 32); /* Initialize canary */ canary = (unsigned int *)(wc->readchunk + ZT_CHUNKSIZE * 64 - 4); *canary = (CANARY << 16) | (0xffff); /* Enable bus mastering */ pci_set_master(pdev); /* Keep track of which device we are */ pci_set_drvdata(pdev, wc); if (request_irq(pdev->irq, t1xxp_interrupt, SA_INTERRUPT | SA_SHIRQ, "wcte11xp", wc)) { printk("wcte11xp: Unable to request IRQ %d\n", pdev->irq); kfree(wc); return -EIO; } /* Initialize hardware */ t1xxp_hardware_init(wc); /* We now know which version of card we have */ wc->variety = "Digium Wildcard TE110P T1/E1"; /* Misc. software stuff */ t1xxp_software_init(wc); printk("Found a Wildcard: %s\n", wc->variety); res = 0; } else res = -ENOMEM; } return res; } static void t1xxp_stop_stuff(struct t1 *wc) { /* Kill clock */ control_set_reg(wc, WC_CLOCK, 0); /* Turn off LED's */ control_set_reg(wc, WC_LEDTEST, 0); } static void __devexit t1xxp_remove_one(struct pci_dev *pdev) { struct t1 *wc = pci_get_drvdata(pdev); if (wc) { /* Stop any DMA */ __t1xxp_stop_dma(wc); /* In case hardware is still there */ __t1xxp_disable_interrupts(wc); t1xxp_stop_stuff(wc); /* Immediately free resources */ pci_free_consistent(pdev, ZT_MAX_CHUNKSIZE * 2 * 2 * 32 * 4, (void *)wc->writechunk, wc->writedma); free_irq(pdev->irq, wc); /* Reset PCI chip and registers */ outb(DELAY | 0x0e, wc->ioaddr + WC_CNTL); /* Release span, possibly delayed */ if (!wc->usecount) t1xxp_release(wc); else wc->dead = 1; } } static struct pci_device_id t1xxp_pci_tbl[] = { { 0xe159, 0x0001, 0x71fe, PCI_ANY_ID, 0, 0, (unsigned long) "Digium Wildcard TE110P T1/E1 Board" }, { 0xe159, 0x0001, 0x79fe, PCI_ANY_ID, 0, 0, (unsigned long) "Digium Wildcard TE110P T1/E1 Board" }, { 0xe159, 0x0001, 0x795e, PCI_ANY_ID, 0, 0, (unsigned long) "Digium Wildcard TE110P T1/E1 Board" }, { 0xe159, 0x0001, 0x79de, PCI_ANY_ID, 0, 0, (unsigned long) "Digium Wildcard TE110P T1/E1 Board" }, { 0xe159, 0x0001, 0x797e, PCI_ANY_ID, 0, 0, (unsigned long) "Digium Wildcard TE110P T1/E1 Board" }, { 0 } }; MODULE_DEVICE_TABLE(pci,t1xxp_pci_tbl); static struct pci_driver t1xxp_driver = { name: "wcte11xp", probe: t1xxp_init_one, #ifdef LINUX26 remove: __devexit_p(t1xxp_remove_one), #else remove: t1xxp_remove_one, #endif suspend: NULL, resume: NULL, id_table: t1xxp_pci_tbl, }; static int __init t1xxp_init(void) { int res; res = zap_pci_module(&t1xxp_driver); if (res) return -ENODEV; return 0; } static void __exit t1xxp_cleanup(void) { pci_unregister_driver(&t1xxp_driver); } #ifdef LINUX26 module_param(alarmdebounce, int, 0600); module_param(loopback, int, 0600); module_param(t1e1override, int, 0600); module_param(clockextra, int, 0600); module_param(debug, int, 0600); #else MODULE_PARM(alarmdebounce, "i"); MODULE_PARM(loopback, "i"); MODULE_PARM(t1e1override, "i"); MODULE_PARM(clockextra, "i"); MODULE_PARM(debug, "i"); #endif MODULE_DESCRIPTION("Wildcard TE110P Zaptel Driver"); MODULE_AUTHOR("Mark Spencer "); #ifdef MODULE_LICENSE MODULE_LICENSE("GPL"); #endif module_init(t1xxp_init); module_exit(t1xxp_cleanup);