XPP revision 3965:

* Tested with zaptel-1.2.17.1
* Add D-Channel TX, RX and BAD frames count in /proc/xpp/XBUS-*/XPD-*/bri_info
* Adjust output of xpp_sync script. Pad for 8 port BRI.
* Added a debugging module parport_debug (not compiled by default).
* Added an optional patch to zaptel:
    - compiles only if ZAPTEL_SYNC_TICK is defined
    - Allow interested driver to register for "sync" notification.
    - Does not affect drivers that do not use this feature.
* Added external synchronization feature:
    - Only if ZAPTEL_SYNC_TICK feature is compiled in
    - Than XPP may be synchronized by another card (e.g: an Astribank
      with FXS can be synchronized by a Digium PRI card).
    - May be enabled/disabled in runtime via the 'sync_tick_active' module
      parameter to the xpp.ko module.
* Fixed a potential bug in D-Channel hexdump printing.
* New visual indications in BRI leds:
    - Constant ON RED/GREEN: Shows the port type -- NT/TE.
    - Very fast "double blink": Layer1 work, no D-Channel yet.
    - Steady blinking (1/2 sec): D-Channel trafic detected.
* xpp_fxloader moved to /usr/share/zaptel .
* adj_clock removed: never really used.
* Now we have Zaptel::Hardware and a sample zaptel_hardware script (not
  (installed by default).
* We also have a sample perl zapconf (not installed by default) which
  aims at replacing genzaptelconf (sans the modules detection).


git-svn-id: http://svn.digium.com/svn/zaptel/trunk@2537 5390a7c7-147a-4af0-8ec9-7488f05a26cb

1 files changed, 14 insertions, 5 deletions

diff --git a/xpp/README.Astribank b/xpp/README.Astribank
index 102ae62..a240f36 100644
--- a/xpp/README.Astribank
+++ b/xpp/README.Astribank
@@ -49,9 +49,9 @@ All firmware files should be copied to a new directory:
 The xpp_fxloader and xpp_fxloader.usermap should be copied to:
  /etc/hotplug/usb/
 
-Note that loading through udev is not yet provided. Run 
+Run:
 
-  /etc/hotplug/usb/xpp_fxloader load
+  /usr/share/zaptel/xpp_fxloader load
 
 to load firmware.
 
@@ -114,10 +114,10 @@ Zaptel as a single span. This will basically be 8 analog channels.
 
 Loading Firmware:
 """"""""""""""""
-Normally this is done using the script xpp_fxloader.If it works fine,
-you don't need to bother reading this section. 
+Normally this is done using the script /usr/share/zaptel/xpp_fxloader .
+If it works fine, you don't need to bother reading this section. 
 Once the firmware is loaded the USB ID of the Astribank changes to e4e4
-1132, and the driver can pick it up. You'll also see the top led lit.
+11x2, and the driver can pick it up. You'll also see the top led lit.
 
 First and foremost: the simplest and most useful tool to debug problems
 here is lsusb. The output of lsusb should show exactly if the device is
@@ -211,6 +211,15 @@ Newer versions of the USB firmware can now be reset using 'fpga_load -r'.
 This will only work when the device is not used by the driver, so you may 
 need to 'rmmod xpp_usb' in order to reset the firmware.
 
+Also try:  
+
+  rmmod xpp_usb; /usr/share/zaptel/xpp_fxloader reset
+  # if asterisk was running: you may need to stop/restart it now. 
+  # if there are some "disconnected" spans in /proc/xpp/xbuses
+  # wait a while, until you see the 1152 IDs again, and then:
+  /etc/init.d/zaptel start
+  # and start/restrart asterisk.
+
 
 Loading The Modules:
 """""""""""""""""""