| Age | Commit message (Collapse) | Author |
|---|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@4367 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* New firmware protocol version: 3.0 .
* New numbers for the device types: (e.g. in card_init* scripts)
- FXS: 1 (was: 3)
- FXO: 2 (was: 4)
- BRI: 3 (was: 6 for TE, 7 for NT)
- PRI: 4 (was: 9)
* Init scripts of FXS and FXO modules are now written in Perl as well
(be sure to have File::Basename, e.g: perl-modules in Debian).
* calibrate_slics merged into init_card_1_30 .
* Module parameter print_dbg replaced with debug . Same meaning.
* init_fxo_modes removed: content moved into init_card_2_30, verified
at build time.
* Code tested with sparse. Most warnings were fixed.
* Set ZT_SIG_DACS for the bchans in the PRI and BRI modules to not get
ignored by ztscan.
* Handle null config_desc we get from some crazy USB controllers.
* genzaptelconf: Fix reporting of empty slots in list mode.
* xpp_blink can now blink a single analog port.
* "slics" has been renamed "chipregs".
* Fixed a small typo in fpga_load(8).
* Fixed bashism in xpp_fxloader.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@4264 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Build:
- Zaptel >= 1.4.9 is migrating to storing kernel stuff in zaptel/kernel/*
- We conditionally use old/new directory scheme:
In xpp/Kbuild and xpp/utils/Makefile use ZAP_KERNEL variable, so it's
not confused with ZAPTEL_DIR (which appears in zaptel/Makefile as well).
- Fix compile warnings on 64 bit systems.
- Compile fixes for kernel-2.6.24
* UDEV:
- /etc/udev/rules.d/xpp.rules now uses XPP_INIT_DIR to find astribank_hook.
- astribank_hook: Modify to do nothing. Add some documentation.
* Autoconfiguration -- zapconf:
- Don't fail zapconf et.al. if no config file was found.
- Skip the 'IRQ Missing:' line in /proc/zaptel/nnn for wcte1xp(?).
- Add some newer Digium cards to our hardware inventory.
- Partially handle cases where the /proc/zaptel strings does not contain
info about E1/T1/J1 or NT/TE.
* Better SYNC:
- Finer tuning of PLL (New firmware).
- Change calculation algorithm of sync offset. It now copes better
with the variance in USB frame reception timing.
- Statistics:
. The view of results was moved from /proc/xpp/XBUS-*/summary to
a new /sys/bus/astribanks/devices/xbus-*/timing and enhanced.
. A new xpp_timing script shows all astribanks.
. A new write only /sys/bus/astribanks/devices/xbus-*/cls is
used to clear statistics. Eventually, clearing of XBUS related
statistics should be done here. One that was migrated is the
clearing of 'PCM [TR]X:' numbers currently appearing in
/proc/xpp/XBUS-*/summary (they should be moved too later).
- Shorten the strings representation sync_mode ("SYNC_MODE_AB" -> "AB")
adapted their use in printk and /proc so the text is clear.
- Added a command line parameter xpp.disable_pll_sync to stop all
adjustments command to AB (calculations still continue as usual).
* PRI:
- 4 port support
- set clocking master span via ztcfg, like other zaptel devices.
* FXO:
- Fix false hangups in some countries (voltage fluctuations).
- Some countries send caller-id before first ring.
Added code to handle caller-id PCM pass through according to
a new command line parameter (xpd_fxo.caller_id_style).
- No longer sends an event on zt_open. See #12160 .
* Misc:
- Adapt to zaptel-1.4.8 and above ztscan: added fields returend by
new ZT_SPANSTAT_V2 ioctl()
- Document sysfs and waitfor_xpds.
- Miscelaneous optimizations and bugfixes.
- Remove deprecated pcm_tasklet parameter. The rx_tasklet parameter has
replaced it a long time ago.
- Add RX_CMD counter to /proc/xpp/XBUS-*/summary
- Unclutter some of the usb disconnect messages.
- xpp_usb: minor preformance improvements in receive.
Expose the number of pending receive URB's in /proc/xpp/XBUS-*/xpp_usb
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3952 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Improved polarity reversal hangups in FXO (r5194).
Fixed false detection of polarity reversals.
* Optimize xframe allocation, by not zeroing the whole
memory (in get_xframe()).
* Fixed erronous error message that appeared sometimes
from fpga_load during USB renumeration.
* Zaptel::Chans now provides battery() reporting for some FXO
channels (Astribank FXO and wcfxo).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3643 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* xpd_pri: Basically ready.
* PCM synchronization changes:
- Each Astribank unit ticks independently. Each with its own PLL.
- HOST synchronization is gone. Loading of xpp will no longer cause
useless 250 ticks per second if you have no Astribank.
- Synchronization from the zaptel sync master requires setting
ZAPTEL as sync source (xpp_sync ZAPTEL).
* rx_tasklet is now a parameter of the module xpp, rather than of xpp_usb.
* New FPGA firmware: 5128 (1151) / 5122 (1141, 1131):
- Fixes synchronization issues.
- PRI module: E1 should now work.
* perl module and utilities:
- Modules no longer magically scan system on initialization.
- Scanning is by calling explicit methods.
- "Serial" has been renamed "Label". It is basically unique, but
should be modifieble.
- Some basic documentation of zaptel perl modules.
* Default sort order of zt_registration is back to SORT_CONNCTOR.
* zt_registration proc file now shows the number of span registered to
if registered. Try: grep . /proc/xpp/XBUS-*/XPD-*/zt_registration
* genzaptelconf: Allow using a custom command instead of
/etc/init.d/asterisk to start/stop asterisk.
* Fixed the typo "Slagish".
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3506 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Zaptel/Hardware perl modules:
- Use sysfs directly. Don't rely on lspci/lsusb.
- Each device has a description and driver name.
- Zaptel::Hardware::drivers() to show the list of required drivers
for this system (see zaptel_drivers).
- zaptel_hardware shows a description and a (suggested?) driver.
* zt_registration sorts by Serial first and only then by connector.
* USB_FW.hex replaces all the USB_11x0.hex .
- Separate USB interface for the management processor.
- Hence fpga_load can now work even with drivers loaded.
* Fix firmware upgrading.
* Fix manual firmware loading while auto-loading.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3142 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* New firmware protocol version: 2.9 .
* fpga_load: initial clean-ups before interface split.
* genzaptelconf: Don't leave an empty directory behind (4784)
* Increase xpp poll_timeout to 1000ms - useful for CentOS 4 (r4781).
* Fix initialization anoyance: if AB don't answer to polls, don't
waitfor_xpds, and show no waiting XPDs (r4725).
* Disable dtmf_detect by default once again (r4712).
* Don't check twice for asterisk to stop. The second test was done
while Asterisk was still stopping (r4708).
* Support building the kernel with M= instead of with SUBDIRS= , as
used in some newer build systems (r4677).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3105 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Update to zaptel-1.2.18 and zaptel-1.4.3 (r4308 onward)
* Fix a critical race with zaptel synchronization (r4362)
* Added a /proc/xpp/cmds for statistics about command timing (r4360)
* Fix a digit mapping bug with hardware dtmf detection (r4357)
* In xpp/utils/Makefile add perl syntax checks to our scripts (r4337)
* Better USB data error checking (r4336)
* udev rules (xpp.rules) avoid false calls from wrong nodes (r4331)
* Improve hardware detection and reporting in lszaptel,
zaptel_hardware. zapconf is basically functional.
* Leds are blinked synchronously on all Astribanks now (r4262)
* Fix a BRI bug if OPTIMIZE_CHANMUTE was compiled into zaptel (r4258)
(This feature was not yet accepted into official zaptel)
* Removed compile warning about HZ != 1000 (r4218)
* Firmware updates.
* fpga_load now supports USB pathes without zeros (r4211)
* XPD numbers have changed to '<Unit><Subunit>' (r4196)
* Proper support for ZT_VMWI ioctl, if used in zaptel (r4092)
* Fix FXO power denial detection (r4054)
* FXO could accidentally go off-hook with some compilers (r4048)
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2732 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Reverse polarity and power denial detection.
* A short led flash at registration time.
* Add a real version of the xpp modules to them (independent of the Zaptel
version).
* Update our line status even when not registered.
* Fixed a false SIG_CHANGED when inserting or removing cable to FXO.
* Fixed compilation fixes for 2.6.20 (Bug #8982)
* A cleaner fix for the bool changes of 2.6.19 .
* Automatically detect echo_can_state_t at debug time.
* Automaitcally set XPP_DEBUGFS (depending on debugfs) at compile time.
* Bug-fixes to zaptel-helper.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2113 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
XPS Init scripts renamed accordingly.
* Performance improvements for multi-XPD (span) devices.
* Astribank BRI driver (in next commit).
* Changes under /proc:
- XBUS and XPD numbers have two digits.
- Every script wildcard should be replaced from XBUS-? to XBUS-[0-9]*
- Added /proc/xpp/XBUS-*/XPD-*/blink: echo 1 to start and 0 to stop.
* Several countries (South Africa, UAE, anybody else) require a shorter
ring delay. Adjust FXO reg 0x17 (23)'s bits 0:2 to 011.
* Use tasklets to move most of the interrupt PCM copying out of the interrupt.
* Debugfs-based code to dump data to userspace (used to debug BRI D channel).
* Pretend every 2.6.9 actually has later RHEL's typedefs.
* fpga_load supports /dev/bus/usb .
* Fixed physical order sorting in genzaptelconf.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1966 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1724 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
implemented so there will still be some warnings when building xpp against 2.6.19 kernel headers
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1700 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
Merging xpp driver release 1.2 (rev. 2569), originally team/tzafrir/xpp_1.2
* Should build well. Almost final.
* genzaptelconf: Also work when zap_autoreg=0
* README.Astribank updated for rev. 1.2.
* xpp/utils/Makefile: Use $< with cc -c
* Get xpp/utils configuration from autoconf (without changesin top dir)
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1648 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1457 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* FPGA firmware now loaded from PC (for newer models)
* Driver for the FXO module (xpd_fxo.ko)
* Moved most userspace files to the subdirectory utils (see also next commit)
* Explicit license for firmware files
* Optionally avoid auto-registration
* Registers initializations code is done by a userspace script.
* Remove obsolete .inc initialization files (we use user-space init)
* Added an install target to the utils dir.
* Updated README.Astribank accordingly.
* Using RBS signalling, as caller ID did not work well otherwise.
* Better handling of USB protocol errors.
* Fixed some procfs-related races.
* per-card-module ioctls.
* fxotune support.
* opermode support (set through /etc/default/zaptel for now)
* Userspace initialization script can also read registers.
* Power calibration works (and implemented in perl)
* some fine-tuning to the regster initialization parameters.
* Leds turn on before registration and turn off after it.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1212 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@949 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
