| Age | Commit message (Collapse) | Author |
|---|
|
* New firmware protocol version: 3.0 .
* New numbers for the device types: (e.g. in card_init* scripts)
- FXS: 1 (was: 3)
- FXO: 2 (was: 4)
- BRI: 3 (was: 6 for TE, 7 for NT)
- PRI: 4 (was: 9)
* Init scripts of FXS and FXO modules are now written in Perl as well
(be sure to have File::Basename, e.g: perl-modules in Debian).
* calibrate_slics merged into init_card_1_30 .
* Module parameter print_dbg replaced with debug . Same meaning.
* init_fxo_modes removed: content moved into init_card_2_30, verified
at build time.
* Code tested with sparse. Most warnings were fixed.
* Set ZT_SIG_DACS for the bchans in the PRI and BRI modules to not get
ignored by ztscan.
* Handle null config_desc we get from some crazy USB controllers.
* genzaptelconf: Fix reporting of empty slots in list mode.
* xpp_blink can now blink a single analog port.
* "slics" has been renamed "chipregs".
* Fixed a small typo in fpga_load(8).
* Fixed bashism in xpp_fxloader.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@4264 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Improved polarity reversal hangups in FXO (r5194).
Fixed false detection of polarity reversals.
* Optimize xframe allocation, by not zeroing the whole
memory (in get_xframe()).
* Fixed erronous error message that appeared sometimes
from fpga_load during USB renumeration.
* Zaptel::Chans now provides battery() reporting for some FXO
channels (Astribank FXO and wcfxo).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3643 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
XPS Init scripts renamed accordingly.
* Performance improvements for multi-XPD (span) devices.
* Astribank BRI driver (in next commit).
* Changes under /proc:
- XBUS and XPD numbers have two digits.
- Every script wildcard should be replaced from XBUS-? to XBUS-[0-9]*
- Added /proc/xpp/XBUS-*/XPD-*/blink: echo 1 to start and 0 to stop.
* Several countries (South Africa, UAE, anybody else) require a shorter
ring delay. Adjust FXO reg 0x17 (23)'s bits 0:2 to 011.
* Use tasklets to move most of the interrupt PCM copying out of the interrupt.
* Debugfs-based code to dump data to userspace (used to debug BRI D channel).
* Pretend every 2.6.9 actually has later RHEL's typedefs.
* fpga_load supports /dev/bus/usb .
* Fixed physical order sorting in genzaptelconf.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1966 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* FPGA firmware now loaded from PC (for newer models)
* Driver for the FXO module (xpd_fxo.ko)
* Moved most userspace files to the subdirectory utils (see also next commit)
* Explicit license for firmware files
* Optionally avoid auto-registration
* Registers initializations code is done by a userspace script.
* Remove obsolete .inc initialization files (we use user-space init)
* Added an install target to the utils dir.
* Updated README.Astribank accordingly.
* Using RBS signalling, as caller ID did not work well otherwise.
* Better handling of USB protocol errors.
* Fixed some procfs-related races.
* per-card-module ioctls.
* fxotune support.
* opermode support (set through /etc/default/zaptel for now)
* Userspace initialization script can also read registers.
* Power calibration works (and implemented in perl)
* some fine-tuning to the regster initialization parameters.
* Leds turn on before registration and turn off after it.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1212 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@949 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
