| Age | Commit message (Collapse) | Author |
|---|
|
Removing explicit transport definition for endpoints and registrations. It
isn't necessary and isn't generally advised.
ASTERISK-26514 #close
Change-Id: Ifdec5e631962438a4683600968dfa4bfd15909fb
|
|
When channel format changes occurred as a result of an RTP
re-negotiation the bridge was not informed this had happened.
As a result the bridge technology was not re-evaluated and the
channel may have been in a bridge technology that was incompatible
with its formats. The bridge is now unbridged and the technology
re-evaluated when this occurs.
The chan_pjsip module also allowed asymmetric codecs for sending
and receiving. This did not work with all devices and caused one
way audio problems. The default has been changed to NOT do this
but to match the sending codec to the receiving codec. For users
who want asymmetric codecs an option has been added, asymmetric_rtp_codec,
which will return chan_pjsip to the previous behavior.
The codecs returned by the chan_pjsip module when queried by
the bridge_native_rtp module were also not reflective of the
actual negotiated codecs. The nativeformats are now returned as
they reflect the actual negotiated codecs.
ASTERISK-26423 #close
Change-Id: I6ec88c6e3912f52c334f1a26983ccb8f267020dc
|
|
This change adds support for dual stack automatically. No
configuration is required and the IP address and version
in the SIP messages and SDP will be automatically changed
based on the transport over which the message is being
sent. RTP usage has also been changed to listen on both
IPv4 and IPv6 simultaneously to allow media to flow, and
to allow ICE support on both simultaneously. This also
allows failover between IPv6 and IPv4 to work as expected.
ASTERISK-26309 #close
Change-Id: I235a421d8f9a326606d861b449fa6fe3a030572d
|
|
Introduces ice_blacklist configuration in rtp.conf. Subnets listed in the
form ice_blacklist = <subnet spec>, e.g. ice_blacklist =
192.168.1.0/255.255.255.0, are excluded from ICE host, srflx and relay
discovery. This is useful for optimizing the ICE process where a system
has multiple host address ranges and/or physical interfaces and certain
of them are not expected to be used for RTP. Multiple ice_blacklist
configuration lines may be used. If left unconfigured, all discovered
host addresses are used, as per previous behavior.
Documention in rtp.conf.sample.
ASTERISK-26418 #close
Change-Id: Ibee88f80d7693874fda1cceaef94a03bd86012c9
|
|
We use a lot res_calendar, we are very happy with that, especially
because you use libical, the almost alone opensource library that
supports really ical format with all types of recurrency.
Nevertheless, some features are missed for our business use cases.
This first patch adds a new option in calendar.conf:
fetch_again_at_reload. Be my guest for a better name.
If it's true, when you'll launch "module reload res_calendar.so",
Asterisk will download again the calendar.
The business use case is that we have a WebUI with a scheduler planner,
we know when the calendars are modified.
For now, we need to define 1 minute of timeout to have a chance that
our user doesn't wait too long between the modification and the real
test. But it generates a lot of useless HTTP traffic.
ASTERISK-26422 #close
Change-Id: I384b02ebfa42b142bbbd5b7221458c7f4dee7077
|
|
|
|
The pooling, shared_connection, limit, and idlecheck options
are no longer used in res_odbc.
ASTERISK-26389
Change-Id: I2fde7b467d01f9d1c82cc0a339bb4f7e1dd6bbe6
|
|
* Make 'cdrzone=UTC' work properly.
* Fix the documentation of cdr_mysql.conf: it's cdrzone and not timezone
ASTERISK-26359 #close
Change-Id: I2a6f67b71bbbe77cac31a34d0bbfb1d67c933778
|
|
This implements the chan_sip legacy_useroption_parsing option but with a
better name.
* Made the caller-id number and redirecting number strings obtained from
incoming SIP URI user fields always truncated at the first semicolon.
People don't care about anything after the semicolon showing up on their
displays even though the RFC allows the semicolon.
ASTERISK-26316 #close
Reported by: Kevin Harwell
Change-Id: Ib42b0e940dd34d84c7b14bc2e90d1ba392624f62
|
|
|
|
This patch add config to pjsip by endpoint.
;preferred_codec_only=yes
; Respond to a SIP invite with the single most preferred codec
; rather than advertising all joint codec capabilities. This
; limits the other side's codec choice to exactly what we prefer.
ASTERISK-26317 #close
Reported by: AaronAn
Tested by: AaronAn
Change-Id: Iad04dc55055403bbf5ec050997aee2dadc4f0762
|
|
Change-Id: Ie627def9604ae30abd80754f9e6f09874825aec6
|
|
|
|
When 'tlsclientmethod' is not specified in sip.conf, chan_sip uses the OpenSSL
SSLv23_method. This was documented incorrectly in the file sip.conf.sample.
SSLv23_method got its name in the 90s. Today, with OpenSSL 1.0.2, this method
enables (just) the secure TLSv1.0 and TLSv1.2. Or stated differently, that
function should have been called 'secure_method' or 'automatic_method' back in
the 90s.
Consequently please, specify 'tlsclientmethod=tlsv1' in your sip.conf only if
you face a server which has problems like not falling back to TLSv1.0
automatically.
ASTERISK-24425
Change-Id: I502ce6146b4504cadfd3973af8d6ec3994f54fa3
|
|
contact_user, when specified on an endpoint, will override the user
portion of the Contact header on outgoing requests.
Change-Id: Icd4ebfda2f2e44d3ac749d0b4066630e988407d4
|
|
|
|
The Exchanging Device and Mailbox States could not working
if the Entity ID (EID) is not set manually and can't be obtained
from ethernet interface.
This patch replaces debug message to warning
and addes missing description about option 'entityid' to
asterisk.conf.sample.
With this patch the asterisk also:
(1) decline loading the modules which won't work without EID:
res_corosync and res_pjsip_publish_asterisk.
(2) warn if EID is empty on loading next modules:
pbx_dundi, res_xmpp
Starting with v197 systemd/udev will automatically assign "predictable"
names for all local Ethernet interfaces.
This patch also addes some new ethernet prefixes "eno" and "ens".
ASTERISK-26164 #close
Change-Id: I72d712f1ad5b6f64571bb179c5cb12461e7c58c6
|
|
ASTERISK-26246 #close
Change-Id: Id673b9786389f9d2a87f638ce1a25161f5f31657
|
|
Make it clear that we're talking about device state hints and add
an entry to the sample config.
Change-Id: Iaef58ffb960191a21b713e8e0b51ce1fcd47e433
|
|
The PJSIP taskprocessors could be overflowed on startup
if there are many (thousands) realtime endpoints
configured with unsolicited mwi.
The PJSIP stack could be totally unresponsive for a few minutes
after boot completed.
This patch creates a separate PJSIP serializers pool for mwi
and makes unsolicited mwi use serializers from this pool.
This patch also adds 2 new global options to tune taskprocessor
alert levels: 'mwi_tps_queue_high' and 'mwi_tps_queue_low'.
This patch also adds new global option 'mwi_disable_initial_unsolicited'
to disable sending unsolicited mwi to all endpoints on startup.
If disabled then unsolicited mwi will start processing
on next endpoint's contact update.
ASTERISK-26230 #close
Change-Id: I4c8ecb82c249eb887930980a800c9f87f28f861a
|
|
On heavy loaded system with IMAP or DB storage,
'app_voicemail' taskprocessor queue could reach 500 scheduled tasks.
It could happen when the IMAP or DB server dies or is unreachable.
It could happen on startup when there are many (thousands)
realtime endpoints configured with unsolicited mwi.
If the taskprocessor queue reaches the high water level
then the alert is triggered and pjsip stops processing new requests
until the queue reaches the low water level to clear the alert.
This patch adds 2 new 'general' configuration options
to tune taskprocessor alert levels:
'tps_queue_high' - Taskprocessor high water alert trigger level.
'tps_queue_low' - Taskprocessor low water clear alert level
ASTERISK-26229 #close
Change-Id: I766294fbffedf64053c0d9ac0bedd3109f043ee8
|
|
Change-Id: Idf97e3a72f1edc5fca58f2fa7b20785922be0cae
|
|
Change-Id: I11139a4a95df34e223ba622aa6227e33ab8f6c38
|
|
The new option allows the channel driver's faxdetect option to timeout on
a call after the specified number of seconds into a call. The new feature
is disabled if the timeout is set to zero. The option is disabled by
default.
* Don't clear dsp_features after passing them to the dsp code in
my_pri_ss7_open_media(). We should still remember them especially for the
new faxdetect_timeout option.
ASTERISK-26214
Reported by: Richard Mudgett
Change-Id: Ieffd3fe788788d56282844774365546dce8ac810
|
|
The new endpoint option allows the PJSIP channel driver's fax_detect
endpoint option to timeout on a call after the specified number of
seconds into a call. The new feature is disabled if the timeout is set
to zero. The option is disabled by default.
ASTERISK-26214
Reported by: Richard Mudgett
Change-Id: Id5a87375fb2c4f9dc1d4b44c78ec8735ba65453d
|
|
Following the principle of least surprise, we should not be sending
massive numbers of PJSIP and RTCP HEP packets out into the ether to some
only-slightly-random IP address. Having 'enabled' set to 'no' in the
sample configuration file should prevent this from happening for those
who run 'make samples'.
ASTERISK-26159 #close
Change-Id: I1753a64ca83a3442a6ebdc31061f8185c062d9b1
|
|
This patch removes the following modules:
- pbx_functions: It never existed.
- res_pjsip_log_forwarder: It no longer exists.
- res_hep_pjsip: The base HEP module wasn't loaded, and most basic PBXs
aren't going to be installing HOMER
- res_pjsip_phoneprov_provider: The basic res_phoneprov module isn't
loaded, and we aren't configured to make use of the
module
Change-Id: Id91f68cae7c9c8c3d370029fe1268cb51e4ff5a5
|
|
|
|
Testing has shown that our usage of UnixODBC is problematic
due to bugs within UnixODBC itself as well as the heavy weight
cost of connecting and disconnecting database connections, even
when pooling is enabled.
For users of UnixODBC 2.3.1 and earlier crashes would occur due
to insufficient protection of the disconnect operation. This was
fixed in UnixODBC 2.3.2 and above.
For users of UnixODBC 2.3.3 and higher a slow-down would occur
under heavy database use due to repeated connection establishment.
A regression is present where on each connection the database
configuration is cached again, with the cache growing out of
control.
The connection pool implementation present in this change helps
to mitigate these issues by reducing how much we connect and
disconnect database connections. We also solve the issue of
crashes under UnixODBC 2.3.1 by defaulting the maximum number of
connections to 1, returning us to the previous working behavior.
For users who may have a fixed version the maximum concurrent
connection limit can be increased helping with performance.
The connection pool works by keeping a list of active connections.
If the connection limit has not been reached a new connection is
established. If the connection limit has been reached then the
request waits until a connection becomes available before
continuing.
ASTERISK-26074 #close
ASTERISK-26054 #close
Change-Id: I6774bf4bac49a0b30242c76a09c403d2e856ecff
|
|
ASTERISK-20527 #close
Change-Id: I659cf7f00836a09d09d146ad226a40477d731239
|
|
Add the option 'enable_callee_prompt' to followme.conf. Enabled by
default. If disabled, a callee is not prompted to accept or reject
the forwarded call.
ASTERISK-26064 #close
Change-Id: I0a8b19d4cf95c86a07c992813babb9e4a4acfff5
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
|
|
|
|
func_odbc was changed in Asterisk 13.9.0
to make func_odbc use a single database connection per DSN
because of reported bug ASTERISK-25938
with MySQL/MariaDB LAST_INSERT_ID().
This is drawback in performance when func_odbc is used
very often in dialplan.
Single database connection should be optional.
ASTERISK-26010
Change-Id: I7091783a7150252de8eeb455115bd00514dfe843
|
|
|
|
A ':' is not a valid token for starting a comment.
Change-Id: I123592d93a83d1bdde3e352822881eb9da85e5ad
|
|
At one point in time, it seemed like a good idea to use the Asterisk
channel name as the HEP correlation UUID. In particular, it felt like
this would be a useful identifier to tie PJSIP messages and RTCP
messages together, along with whatever other data we may eventually send
to Homer. This also had the benefit of keeping the correlation UUID
channel technology agnostic.
In practice, it isn't as useful as hoped, for two reasons:
1) The first INVITE request received doesn't have a channel. As a
result, there is always an 'odd message out', leading it to be
potentially uncorrelated in Homer.
2) Other systems sending capture packets (Kamailio) use the SIP Call-ID.
This causes RTCP information to be uncorrelated to the SIP message
traffic seen by those capture nodes.
In order to support both (in case someone is trying to use res_hep_rtcp
with a non-PJSIP channel), this patch adds a new option, uuid_type, with
two valid values - 'call-id' and 'channel'. The uuid_type option is used
by a module to determine the preferred UUID type. When available, that
source of a correlation UUID is used; when not, the more readily available
source is used.
For res_hep_pjsip:
- uuid_type = call-id: the module uses the SIP Call-ID header value
- uuid_type = channel: the module uses the channel name if available,
falling back to SIP Call-ID if not
For res_hep_rtcp:
- uuid_type = call-id: the module uses the SIP Call-ID header if the
channel type is PJSIP and we have a channel,
falling back to the Stasis event provided
channel name if not
- uuid_type = channel: the module uses the channel name
ASTERISK-25352 #close
Change-Id: Ide67e59a52d9c806e3cc0a797ea1a4b88a00122c
|
|
|
|
|
|
|
|
|
|
* No need to set language in a miniml configuration. 'en' will do just
fine.
* It would be useful to have an example of setting it to a different
language.
* Setting the documentation language explicitly is likewise not
required. Setting it to a different value is not common. At least
until there is a set of translated documentation.
Change-Id: I94d91ea34e129925f25af81ef8dc0906fb568cb7
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
|
|
Don't suggest users to use debug level 5, which spews (usually
non-useful) debug information. Reduce the suggestion to (an
arbitrarily-selected) level 2.
Change-Id: Ib53195f78945970956ff59ef13fa89b90e0fcd60
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
|
|
Note the default of remmed-out options. To clarify that those values are
not the defaults.
Change-Id: I849c29b7a710f0abc37355fcb5bfee335ae30738
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
|
|
A minimal configuration does not need to explicitly spell out the
directories. The built-in defaults will do just fine. In many cases
they are wrong.
Change-Id: Id1a671e5c5e9923765a4156b57f9f7e263fdd26c
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
|
|
This patch allows for having app_confbridge register the name of the
conference as an extension into a specific context, similar to
regcontext for chan_sip. This variant is not quite as involved as the
one in chan_sip and doesn't allow for multiple contexts or custom
extensions, you can only specify the context and the conference name
will always be used as the extension to register.
ASTERISK-25989 #close
Change-Id: Icacf94d9f2b5dfd31ef36f6cb702392619a7902f
|
|
Note: When packagers use these files (as an example) the paths are never
really used when they are split using '='.
Note: Thirdparty applications will also have trouble parsing the file when
expecting '=>'.
Change-Id: I0ada647f588e81f023fb1333ca15a1a333fd6004
|
|
A feature of chan_sip that service providers relied upon was the ability to
identify by the Authorization username. This is most often used when customers
have a PBX that needs to register rather than identify by IP address. From my
own experiance, this is pretty common with small businesses who otherwise
don't need a static IP.
In this scenario, a register from the customer's PBX may succeed because From
will usually contain the PBXs account id but an INVITE will contain the caller
id. With nothing recognizable in From, the service provider's Asterisk can
never match to an endpoint and the INVITE just stays unauthorized.
The fixes:
A new value "auth_username" has been added to endpoint/identify_by that
will use the username and digest fields in the Authorization header
instead of username and domain in the the From header to match an endpoint,
or the To header to match an aor. This code as added to
res_pjsip_endpoint_identifier_user rather than creating a new module.
Although identify_by was always a comma-separated list, there was only
1 choice so order wasn't preserved. So to keep the order, a vector was added
to the end of ast_sip_endpoint. This is only used by res_pjsip_registrar
to find the aor. The res_pjsip_endpoint_identifier_* modules are called in
globals/endpoint_identifier_order.
Along the way, the logic in res_pjsip_registrar was corrected to match
most-specific to least-specific as res_pjsip_endpoint_identifier_user does.
The order is:
username@domain
username@domain_alias
username
Auth by username does present 1 problem however, the first INVITE won't have
an Authorization header so the distributor, not finding a match on anything,
sends a securty_alert. It still sends a 401 with a challenge so the next
INVITE will have the Authorization header and presumably succeed. As a result
though, that first security alert is actually a false alarm.
To address this, a new feature has been added to pjsip_distributor that keeps
track of unidentified requests and only sends the security alert if a
configurable number of unidentified requests come from the same IP in a
configurable amout of time. Those configuration options have been added to
the global config object. This feature is only used when auth_username
is enabled.
Finally, default_realm was added to the globals object to replace the hard
coded "asterisk" used when an endpoint is not yet identified.
The testsuite tests all pass but new tests are forthcoming for this new
feature.
ASTERISK-25835 #close
Reported-by: Ross Beer
Change-Id: I30ba62d208e6f63439600916fcd1c08a365ed69d
|
|
This patch added new global pjsip option 'disable_multi_domain'.
Disabling Multi Domain can improve Realtime performance by reducing
number of database requests.
ASTERISK-25930 #close
Change-Id: I2e7160f3aae68475d52742107949a799aa2c7dc7
|
|
Option was removed in commit 7f883ef495b57ae9182e47213d01d5e8009dbf3f
ASTERISK-25927 #close
Change-Id: I92f9b0196d9fc41d1d58354c07340c465ef1fcf8
|
|
res_pjsip_mwi was missing the chan_sip "vmexten" functionality which adds
the Message-Account header to the MWI NOTIFY. Also, specifying mailboxes
on endpoints for unsolicited mwi and on aors for subscriptions required
that the admin know in advance which the client wanted. If you specified
mailboxes on the endpoint, subscriptions were rejected even if you also
specified mailboxes on the aor.
Voicemail extension:
* Added a global default_voicemail_extension which defaults to "".
* Added voicemail_extension to both endpoint and aor.
* Added ast_sip_subscription_get_dialog for support.
* Added ast_sip_subscription_get_sip_uri for support.
When an unsolicited NOTIFY is constructed, the From header is parsed, the
voicemail extension from the endpoint is substituted for the user, and the
result placed in the Message-Account field in the body.
When a subscribed NOTIFY is constructed, the subscription dialog local uri
is parsed, the voicemail_extension from the aor (looked up from the
subscription resource name) is substituted for the user, and the result
placed in the Message-Account field in the body.
If no voicemail extension was defined, the Message-Account field is not added
to the NOTIFY body.
mwi_subscribe_replaces_unsolicited:
* Added mwi_subscribe_replaces_unsolicited to endpoint.
The previous behavior was to reject a subscribe if a previous internal
subscription for unsolicited MWI was found for the mailbox. That remains the
default. However, if there are mailboxes also set on the aor and the client
subscribes and mwi_subscribe_replaces_unsolicited is set, the existing internal
subscription is removed and replaced with the external subscription. This
allows an admin to configure mailboxes on both the endpoint and aor and allows
the client to select which to use.
ASTERISK-25865 #close
Reported-by: Ross Beer
Change-Id: Ic15a9415091760539c7134a5ba3dc4a6a1217cea
|
