Age | Commit message (Collapse) | Author |
|
* Fix an issue due to long firmware load time:
- When one Astribank has an echo canceler (long firmware loading) and
and another one does not.
- The EC-less Astribank finishes initialization before the Astribank
with EC is detected.
- Thus waitfor_xpds terminates too early.
* We now iteratively build two sets of serial numbers:
- One from wha we see in all Xorcom (e4e4:11[3456]x) USB devices.
- The other is those that were detected in the driver.
- Only when the two sets are equal (and > 0) we know we are done.
- This is resilient to many problems (e.g: disconnect/reconnect of
same device during initialization).
* The progress output was also improved: Now each detected AB
show the total number so far.
* The timeout was also increased to 100sec
* Woraround for an Astribank with no serial (but just a single one on
the system).
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10465
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10737 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10701
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10703 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Adding the TE820 vendor and device ID into PCI.pm allows dahdi_hardware to
recognize the card.
Reported-by: Xavier Hienne
Internal-Issue-ID: DAHTOOL-58
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10680
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10682 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
When running the astribank_hook (only on Astribanks, in XPP_HOTPLUG_DAHDI
mode), wait for all other Astribanks to create all the required device
files.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10585
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10596 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Remove a useless debug message in the "write" operation.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10549
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10555 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Unlike original: also fixed fpga_load.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10543
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10548 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10542
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10547 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10505
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10523 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Fixed 'astribanks_tool' string
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10503
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10522 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* License strings markers (BEGIN.../END...) can be customized
* By default, generate a "generic" license markers
* We accept any (paired) markers from the valid list
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10502
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10521 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* I/O errors of the device were not propagated up by echo_loader
* As a result, Octasic load failure did not prevented USB renumeration
* Make consistent return values:
- In our functions: ret < 0 is error
- In Octasic functions (UINT32): return Octasic error codes
* All error paths prints error messages (so we see how the error propagates)
* Also changed error order testing in init_octasic():
Return status should be tested before the values of by-reference parameters
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10499
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10520 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Define new macros AB_INFO(), AB_ERR() that prefix their message
with the astribank information (usb device + serial number)
* Replace all INFO()/ERR() messages in echo_loader.c with the new macros
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10498
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10519 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Use the new dahdi_sysfs_copy script
* Clean old/unused code
* Add notification output
* Now always creates a tarball - the gzipped copy is many times smaller.
* Without arguments, tarball name is:
sys_dump.<hostname>_<date>_<time>.tar.gz
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10497
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10518 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Short perl script to copy dahdi related sysfs trees
into a designated directory.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10496
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10517 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Replaced (almost) all $LOGGER to echo:
- In interactive use -- that what we want anyway
- When called from UDEV, the subprocess stdout/stderr is piped to
$LOGGER anyway (at the end of the script)
- No need for many $LOGGER instances (each with its own pid)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10495
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10516 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Extrainfo field contains junk data
* Caused by:
- The field is initialized to 0xFF values
- There was no null termination (and no room to add it)
* New code:
- Ensure that show_extrainfo() have null termination even if EEPROM
field is full.
- Replace trailing 0xFF characters with '\0' when reading this field
- Since our default burned EEPROM contain Extrainfo field full of
0xFF characters, this would make them look as null filled.
Internal Issue-Id: #1341
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Origin: http://svnview.digium.com/svn/dahdi?view=rev&rev=10491
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10515 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/branches/2.6@10407 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Two extra USB product IDs used in some odd maintenance scenarios.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10368 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Avoid a duplicated run of udev on some systems.
* Fix usage of astribank_tool's output.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10366 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
(Closes issue DAHTOOL-56)
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10358 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
USB_RECOV.hex is an extra firmware that may be useful for recovering
from certain Astribank hardware faults in some scenarios. This adds
support for either loading it manually
('/usr/share/dahdi/xpp_fxloader recover-sb') or through udev, *if*
the required udev rules were set on the system.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10349 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
This introduces support for loading multiple firmwares in parallel also
for the case of a manual load. This is anyway the case for an automatic
load from udev.
* libusb needs to scan the bus all too often. This causes occasional
failures for opening devices.
* Thus introduce a semaphore to serialize uses of libusb.
E-Main-3 firmware differs by a different value of bcdDevice:
* Read this from the sysfs devices tree.
* Fall back to lsusb -v (much slower) is sysfs not available.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10348 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Newer firmwares may have more lines.
* While we're at it, add better debug printing.
* Remove some unused debugging code.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10343 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10311 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10308 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* dahdi_cfg -S <num>: only apply changes to span <num>.
* If span is analog (no 'span=<num>,<channels>,...' statement in
system.conf), we need to set range: -C <channels>
* With the <basechan> and <channels> attributes in sysfs
we easily configure each device on the fly.
Simply run: dahdi_cfg -S <spanno> -C <basechan>+<channels>-1
from udev script
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10306 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
This utility will export packet captures for channels in dahdi. It requires
CONFIG_DAHDI_MIRROR to be defined in dahdi-linux as it uses the unsupported
DAHDI_MIRROR ioctl interface.
Internal-Issue-ID: DAHTOOL-49
From: Torrey Searle <tsearle@gmail.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10293 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10267 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
The xpp_order configuration generator should only loop over telephony
devices, not all spans.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10266 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Don't force extens we generate to have exactly 4 digits (simple
formatting limitation).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10265 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10264 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Also makes sure that the percentage output from the verbose and
non-verbose modes of timer_test are the same and print a cumulative
accuracy which smooths out the jitter for each pass.
If the time it takes to read in 1 second worth of data is longer than 1
second accuracy will be 0%.
(closes issue #18573)
Reported by: smurfix
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10216 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Warn the user if attempting to monitor a statistic that the particular
board driver does not appear to be collecting. The wcte12xp in r10212 in
now fills in -1 for any statistic it does not collect and other digital
cards can do the same.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10215 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
The wcb4xxp driver does not put enough information in the proc filesystem to
determine if the ports are in TE or NT mode. Previously the ports would
always just setup the dahdi-channels.conf file in TE mode. After this change
the dahdi_scan utility is used to detect if the ports are in TE or NT mode and
setup dahdi-channels.conf appropriately.
Internal-Issue-ID: DAHTOOL-54
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10214 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Resolves a regression on the 2.5 branch that would result in:
$ dahdi_genconf
dahdi_genconf: missing default group (termtype=UNKNOWN)
E1 / T1 spans use software configuration to set CPE / NET mode. This
patch will just assume that a termtype is software selectable if it was
"UNKNOWN" when first scanning the span.
Internal-Issue-ID: DAHTOOL-55
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Tested-by: David Purdue <support@noojee.com.au>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10213 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Fix dahdi_maint's usage message while we're at it.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10198 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10196 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10194 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
On several pathological cases we may need to wait more than 40 seconds.
Make that timeout configurable.
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10177 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10153 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Use 'dahdi_genconf freepbxdb' to generate the required astdb entries
for Asterisk to use the extensions generated by dahdi_genconf. Requires
asterisk to be running.
This module is intended for testing as it bypasses standard FreePBX
functions only and hence may not work properly with Freepbx.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10142 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10104 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Match complete span patterns, to avoid pattern 'SPAN/1' from matching
e.g. span 12 (SPAN/12).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10101 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10087 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10085 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Fixes the feature introduced in r9909 that allows patlooptest to
monitor channel events. Patlooptest was reporting events that we don't
care about, prior to reading from the channel. This fix ignore the first
event read on a channel and reports all subsequent events properly.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10071 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
* Silently exit right away if user did not set XPP_HOTPLUG_DAHDI.
* Only one Astribank should be allowed to run the startup script:
- Protect that section with a "lock" (symlinking a file).
- Sadly we can't rely on /run and may have to wait for a r/w file-system.
- And thus even this waiting needs to be run in the background
as to not hold udev.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10068 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
It is possible that the contents of the proc files can change while the
perl modules are in the processing of processing them.
Specifically, if lsdahdi is called on boot before the channels are
configured, the channel will be "probed" to determine if it's an FXO or
FXS channel and that can result in the output of proc changing. When the
size of proc changes, the script can get confused about where the
beginning of the next line is.
This patch reads in the proc file completely into memory first, and then
starts processing each of the lines.
This resolves the "Unrecognized garbage 'INACTIVE)' in -" that is
displayed on boot with the recent trunk of DAHDI.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10040 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Hardwire this for now, as this does not come from autoconf.
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10034 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|
|
Echo Cancellation firmware is loaded by xpp/stribank_hexload
(Using the oct612x code).
* astribank_hexload: options -O/-o/-A for handling the Octasic echo
cancellation firmware.
* astribank_tool: report that.
* xpp_fxloader: Run astribank_hexload, if needed.
* dahdi_perl: The EC module is an extra XPD, but not a "telephony device"
and hence not a span. Deal with that.
* waitfor_xpds: may need to wait a bit longer for firmware loading.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/tools/trunk@10032 a0bf4364-ded3-4de4-8d8a-66a801d63aff
|