|
For finer details and separate commits, you are advised to look into the
commit log of dahdi-{linux,tools}.
xpp.r7150
* 116x Astribanks:
- Support for the TwinStar capability and for FXO and (BRI|PRI) on
same device.
- New control protocol ("MPP").
- astribank_hextool - a low-level firmware loading tool instead of
fpga_load .
- astribank_tool - Other MPP activities .
- Can still reset (but just that) through older protocol.
- astribank_hexload is required for loading FPGA firmware for USB_FW.hex
rev > 6885.
- USB_FW rev. 7071 .
- More modular FPGA firmware (1161 only).
- FPGA_1161.hex rev. 7131. PIC_TYPE_* rev. 7107.
- software-settings of some capabilities with astribank_allow .
* XPP:
- init_card_* script are less verbose.
- Reduced rate of "Is a DAHDI sync master" message.
- Replace member bus_id with dev_name() and set_dev_name() for
building with 2.6.30.
- Conditionally remove 'owner' property of procfs was dropped in 2.6.30.
- astribank_hook now enabled by default.
- Has an optional hook for TwinStar.
* BRI:
- hardhdlc support: The bri_dchan patch is no longer needed.
- If bri_dchan patch applied: old code is used, and "dchan" is used.
- If not: new code and "hardhdlc" is used.
- zapconf will generate the right configuration, depending on the new
sysfs driver attribute bri_hardhdlc, but default to "dchan" as
before if not explicitly told.
- Bugfix: explicitly turn off leds on startup.
* FXS:
- Initialization and calibration fixes.
- Notify the user just one about wrong VMWI config
* Dahdi-perl:
- Fix detection of empty slots in wctdm.
- Fix working with ethmf's extra file in /proc/zaptel
- Improved detection of Rhino cards.
- dahdi_genconf's generated text better explains files are generated.
- /etc/xpp_order - allow specifiying an explicit order for
Astribanks to register with Zaptel.
- Dahdi::Xpp::Mpp - A wrapper around astribank_tool .
* dahdi.init:
- A separate waitfor_xpds script. May now have a wait-loop in
some cases.
- xpp_sync needs to only be called after dahdi_cfg .
(for the PRI module).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.4@4641 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
Sun Mar 1 2009 Oron Peled <oron@actcom.co.il> - xpp.r6795
* Fix cases where the command_queue overflowed during initialization.
- Also add a 'command_queue_length' parameter to xpp.ko
* More migrations to sysfs:
- Add a 'transport' attribute to our astribank devices which
points to the usb device we use. E.g:
/sys/bus/astribanks/devices/xbus-00/transport is symlinked to
../../../../../../devices/pci0000:00/0000:00:10.4/usb5/5-4
- Move /proc/xpp/XBUS-??/XPD-??/span to
/sys/bus/xpds/devices/??:?:?/span
- Migrate from /proc/xpp/sync to:
/sys/bus/astribanks/drivers/xppdrv/sync
- New 'offhook' attribute in:
/sys/bus/xpds/devices/??:?:?/offhook
* PRI: change the "timing" priority to match the convention used by
other PRI cards -- I.e: lower numbers (not 0) have higher
priority.
* FXO:
- Power denial: create two module parameters instead of hard-coded
constants (power_denial_safezone, power_denial_minlen).
For sites that get non-standard power-denial signals from central
office on offhook.
- Don't hangup on power-denial, just notify Dahdi and wait for
- Fix caller-id detection for the case central office sends it before
first ring without any indication before.
Asterisk's desicion.
Mon, Dec 8 2008 Oron Peled <oron@actcom.co.il> - xpp.r6430
* PRI:
- Match our span clocking priorities (in system.conf)
to Digium -- this is a reversal of the previous state.
Now lower numbers (greater than 0) are better.
- Synchronization fixes for PRI ports other than 0.
- Fix T1 CRC for some countries (e.g: China).
* FXS: fix bug in VMWI detection if using old asterisk
which does not provide ZT_VMWI ioctl().
* FXO:
- Improve caller_id_style module parameter. This provide a workaround
for countries that send this information without any notification
(reverse polarity, ring, etc.)
- Don't force on-hook upon power-denial. So, loopstart devices
would ignore these as expected.
* Implement a flow-control to prevent user space (init_card_* scripts)
from pressuring our command queue.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.4@4631 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
