Age | Commit message (Collapse) | Author |
|
* New firmware protocol version: 3.0 .
* New numbers for the device types: (e.g. in card_init* scripts)
- FXS: 1 (was: 3)
- FXO: 2 (was: 4)
- BRI: 3 (was: 6 for TE, 7 for NT)
- PRI: 4 (was: 9)
* Init scripts of FXS and FXO modules are now written in Perl as well
(be sure to have File::Basename, e.g: perl-modules in Debian).
* calibrate_slics merged into init_card_1_30 .
* Module parameter print_dbg replaced with debug . Same meaning.
* init_fxo_modes removed: content moved into init_card_2_30, verified
at build time.
* Code tested with sparse. Most warnings were fixed.
* Set ZT_SIG_DACS for the bchans in the PRI and BRI modules to not get
ignored by ztscan.
* Handle null config_desc we get from some crazy USB controllers.
* genzaptelconf: Fix reporting of empty slots in list mode.
* xpp_blink can now blink a single analog port.
* "slics" has been renamed "chipregs".
* Fixed a small typo in fpga_load(8).
* Fixed bashism in xpp_fxloader.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@4264 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Build:
- Zaptel >= 1.4.9 is migrating to storing kernel stuff in zaptel/kernel/*
- We conditionally use old/new directory scheme:
In xpp/Kbuild and xpp/utils/Makefile use ZAP_KERNEL variable, so it's
not confused with ZAPTEL_DIR (which appears in zaptel/Makefile as well).
- Fix compile warnings on 64 bit systems.
- Compile fixes for kernel-2.6.24
* UDEV:
- /etc/udev/rules.d/xpp.rules now uses XPP_INIT_DIR to find astribank_hook.
- astribank_hook: Modify to do nothing. Add some documentation.
* Autoconfiguration -- zapconf:
- Don't fail zapconf et.al. if no config file was found.
- Skip the 'IRQ Missing:' line in /proc/zaptel/nnn for wcte1xp(?).
- Add some newer Digium cards to our hardware inventory.
- Partially handle cases where the /proc/zaptel strings does not contain
info about E1/T1/J1 or NT/TE.
* Better SYNC:
- Finer tuning of PLL (New firmware).
- Change calculation algorithm of sync offset. It now copes better
with the variance in USB frame reception timing.
- Statistics:
. The view of results was moved from /proc/xpp/XBUS-*/summary to
a new /sys/bus/astribanks/devices/xbus-*/timing and enhanced.
. A new xpp_timing script shows all astribanks.
. A new write only /sys/bus/astribanks/devices/xbus-*/cls is
used to clear statistics. Eventually, clearing of XBUS related
statistics should be done here. One that was migrated is the
clearing of 'PCM [TR]X:' numbers currently appearing in
/proc/xpp/XBUS-*/summary (they should be moved too later).
- Shorten the strings representation sync_mode ("SYNC_MODE_AB" -> "AB")
adapted their use in printk and /proc so the text is clear.
- Added a command line parameter xpp.disable_pll_sync to stop all
adjustments command to AB (calculations still continue as usual).
* PRI:
- 4 port support
- set clocking master span via ztcfg, like other zaptel devices.
* FXO:
- Fix false hangups in some countries (voltage fluctuations).
- Some countries send caller-id before first ring.
Added code to handle caller-id PCM pass through according to
a new command line parameter (xpd_fxo.caller_id_style).
- No longer sends an event on zt_open. See #12160 .
* Misc:
- Adapt to zaptel-1.4.8 and above ztscan: added fields returend by
new ZT_SPANSTAT_V2 ioctl()
- Document sysfs and waitfor_xpds.
- Miscelaneous optimizations and bugfixes.
- Remove deprecated pcm_tasklet parameter. The rx_tasklet parameter has
replaced it a long time ago.
- Add RX_CMD counter to /proc/xpp/XBUS-*/summary
- Unclutter some of the usb disconnect messages.
- xpp_usb: minor preformance improvements in receive.
Expose the number of pending receive URB's in /proc/xpp/XBUS-*/xpp_usb
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3952 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* xpd_pri: Basically ready.
* PCM synchronization changes:
- Each Astribank unit ticks independently. Each with its own PLL.
- HOST synchronization is gone. Loading of xpp will no longer cause
useless 250 ticks per second if you have no Astribank.
- Synchronization from the zaptel sync master requires setting
ZAPTEL as sync source (xpp_sync ZAPTEL).
* rx_tasklet is now a parameter of the module xpp, rather than of xpp_usb.
* New FPGA firmware: 5128 (1151) / 5122 (1141, 1131):
- Fixes synchronization issues.
- PRI module: E1 should now work.
* perl module and utilities:
- Modules no longer magically scan system on initialization.
- Scanning is by calling explicit methods.
- "Serial" has been renamed "Label". It is basically unique, but
should be modifieble.
- Some basic documentation of zaptel perl modules.
* Default sort order of zt_registration is back to SORT_CONNCTOR.
* zt_registration proc file now shows the number of span registered to
if registered. Try: grep . /proc/xpp/XBUS-*/XPD-*/zt_registration
* genzaptelconf: Allow using a custom command instead of
/etc/init.d/asterisk to start/stop asterisk.
* Fixed the typo "Slagish".
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3506 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* New firmware protocol version: 2.9 .
* fpga_load: initial clean-ups before interface split.
* genzaptelconf: Don't leave an empty directory behind (4784)
* Increase xpp poll_timeout to 1000ms - useful for CentOS 4 (r4781).
* Fix initialization anoyance: if AB don't answer to polls, don't
waitfor_xpds, and show no waiting XPDs (r4725).
* Disable dtmf_detect by default once again (r4712).
* Don't check twice for asterisk to stop. The second test was done
while Asterisk was still stopping (r4708).
* Support building the kernel with M= instead of with SUBDIRS= , as
used in some newer build systems (r4677).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3105 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* BRI improvement: an 'nt_keepalive' parameter to xpd_bri forces
a BRI_NT to retry a connection indefinitely (this is our default).
When false it revert to the behaviour in changeset:4415 ("Bezeq like")
* Improvement in DBG macros. The print_dbg parameter is now set of
flags to debug. They are defined in zap_debug.h
* Don't use Astribanks connected to USB1 interfaces
Unless the user set the option usb1=1 for xpp_usb (r4504).
* And some more documentation...
* Include some of our variables in the default zaptel sample file.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2860 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Show Astribank 6+2 as 6/2 channels and not 8/8 channels.
- Added as a "subtype" to the device type (r4391).
* Fixed a panic in BRI span shutdown method (r4393).
* Changes to debug macros.
* Add proper sysfs support (r4406)
- A bus on whuch all of the Astribanks reside.
- Replaces useless sysfs code that existed in the module.
- Currently used to set the sync source automatically at device
adition / removal.
* BRI: We do need the T1 timer in NT. If it gets into G2 state (rr4407).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2811 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|