Age | Commit message (Collapse) | Author |
|
* Build:
- Zaptel >= 1.4.9 is migrating to storing kernel stuff in zaptel/kernel/*
- We conditionally use old/new directory scheme:
In xpp/Kbuild and xpp/utils/Makefile use ZAP_KERNEL variable, so it's
not confused with ZAPTEL_DIR (which appears in zaptel/Makefile as well).
- Fix compile warnings on 64 bit systems.
- Compile fixes for kernel-2.6.24
* UDEV:
- /etc/udev/rules.d/xpp.rules now uses XPP_INIT_DIR to find astribank_hook.
- astribank_hook: Modify to do nothing. Add some documentation.
* Autoconfiguration -- zapconf:
- Don't fail zapconf et.al. if no config file was found.
- Skip the 'IRQ Missing:' line in /proc/zaptel/nnn for wcte1xp(?).
- Add some newer Digium cards to our hardware inventory.
- Partially handle cases where the /proc/zaptel strings does not contain
info about E1/T1/J1 or NT/TE.
* Better SYNC:
- Finer tuning of PLL (New firmware).
- Change calculation algorithm of sync offset. It now copes better
with the variance in USB frame reception timing.
- Statistics:
. The view of results was moved from /proc/xpp/XBUS-*/summary to
a new /sys/bus/astribanks/devices/xbus-*/timing and enhanced.
. A new xpp_timing script shows all astribanks.
. A new write only /sys/bus/astribanks/devices/xbus-*/cls is
used to clear statistics. Eventually, clearing of XBUS related
statistics should be done here. One that was migrated is the
clearing of 'PCM [TR]X:' numbers currently appearing in
/proc/xpp/XBUS-*/summary (they should be moved too later).
- Shorten the strings representation sync_mode ("SYNC_MODE_AB" -> "AB")
adapted their use in printk and /proc so the text is clear.
- Added a command line parameter xpp.disable_pll_sync to stop all
adjustments command to AB (calculations still continue as usual).
* PRI:
- 4 port support
- set clocking master span via ztcfg, like other zaptel devices.
* FXO:
- Fix false hangups in some countries (voltage fluctuations).
- Some countries send caller-id before first ring.
Added code to handle caller-id PCM pass through according to
a new command line parameter (xpd_fxo.caller_id_style).
- No longer sends an event on zt_open. See #12160 .
* Misc:
- Adapt to zaptel-1.4.8 and above ztscan: added fields returend by
new ZT_SPANSTAT_V2 ioctl()
- Document sysfs and waitfor_xpds.
- Miscelaneous optimizations and bugfixes.
- Remove deprecated pcm_tasklet parameter. The rx_tasklet parameter has
replaced it a long time ago.
- Add RX_CMD counter to /proc/xpp/XBUS-*/summary
- Unclutter some of the usb disconnect messages.
- xpp_usb: minor preformance improvements in receive.
Expose the number of pending receive URB's in /proc/xpp/XBUS-*/xpp_usb
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3952 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Improved polarity reversal hangups in FXO (r5194).
Fixed false detection of polarity reversals.
* Optimize xframe allocation, by not zeroing the whole
memory (in get_xframe()).
* Fixed erronous error message that appeared sometimes
from fpga_load during USB renumeration.
* Zaptel::Chans now provides battery() reporting for some FXO
channels (Astribank FXO and wcfxo).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3643 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* xpd_pri: Basically ready.
* PCM synchronization changes:
- Each Astribank unit ticks independently. Each with its own PLL.
- HOST synchronization is gone. Loading of xpp will no longer cause
useless 250 ticks per second if you have no Astribank.
- Synchronization from the zaptel sync master requires setting
ZAPTEL as sync source (xpp_sync ZAPTEL).
* rx_tasklet is now a parameter of the module xpp, rather than of xpp_usb.
* New FPGA firmware: 5128 (1151) / 5122 (1141, 1131):
- Fixes synchronization issues.
- PRI module: E1 should now work.
* perl module and utilities:
- Modules no longer magically scan system on initialization.
- Scanning is by calling explicit methods.
- "Serial" has been renamed "Label". It is basically unique, but
should be modifieble.
- Some basic documentation of zaptel perl modules.
* Default sort order of zt_registration is back to SORT_CONNCTOR.
* zt_registration proc file now shows the number of span registered to
if registered. Try: grep . /proc/xpp/XBUS-*/XPD-*/zt_registration
* genzaptelconf: Allow using a custom command instead of
/etc/init.d/asterisk to start/stop asterisk.
* Fixed the typo "Slagish".
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3506 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Zaptel/Hardware perl modules:
- Use sysfs directly. Don't rely on lspci/lsusb.
- Each device has a description and driver name.
- Zaptel::Hardware::drivers() to show the list of required drivers
for this system (see zaptel_drivers).
- zaptel_hardware shows a description and a (suggested?) driver.
* zt_registration sorts by Serial first and only then by connector.
* USB_FW.hex replaces all the USB_11x0.hex .
- Separate USB interface for the management processor.
- Hence fpga_load can now work even with drivers loaded.
* Fix firmware upgrading.
* Fix manual firmware loading while auto-loading.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3142 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* New firmware protocol version: 2.9 .
* fpga_load: initial clean-ups before interface split.
* genzaptelconf: Don't leave an empty directory behind (4784)
* Increase xpp poll_timeout to 1000ms - useful for CentOS 4 (r4781).
* Fix initialization anoyance: if AB don't answer to polls, don't
waitfor_xpds, and show no waiting XPDs (r4725).
* Disable dtmf_detect by default once again (r4712).
* Don't check twice for asterisk to stop. The second test was done
while Asterisk was still stopping (r4708).
* Support building the kernel with M= instead of with SUBDIRS= , as
used in some newer build systems (r4677).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3105 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* New firmware protocol version: 2.8 .
* New firmwares fix input ports offhook.
* Cleanup INFO() messages during module loading.
* USB: Receive queue with TASKLETS [r4600]. Controlled by rx_tasklet
parameter to xpp_usb module (can be changed in runtime).
* The pcm_tasklet parameter in xpp module is deprecated:
- Does not actually do anything.
- If set during module loading, shows an ERR() message.
- Also appears in /proc/xpp/sync
* FXS: Hardware DTMF detection by default, can be disabled
by setting dtmf_detection=0 parameter to xpd_fxs.
PCM is muted when DTMF key is pressed.
* zapconf:
- Can now generate users.conf compatible with asterisk-gui.
- Optional command-line arguments denoting which files to generate.
Possible values are 'zaptel', 'zapata' and 'users'.
- Defaults to creating zaptel and zapata.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@3019 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* BRI improvement: an 'nt_keepalive' parameter to xpd_bri forces
a BRI_NT to retry a connection indefinitely (this is our default).
When false it revert to the behaviour in changeset:4415 ("Bezeq like")
* Improvement in DBG macros. The print_dbg parameter is now set of
flags to debug. They are defined in zap_debug.h
* Don't use Astribanks connected to USB1 interfaces
Unless the user set the option usb1=1 for xpp_usb (r4504).
* And some more documentation...
* Include some of our variables in the default zaptel sample file.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2860 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Show Astribank 6+2 as 6/2 channels and not 8/8 channels.
- Added as a "subtype" to the device type (r4391).
* Fixed a panic in BRI span shutdown method (r4393).
* Changes to debug macros.
* Add proper sysfs support (r4406)
- A bus on whuch all of the Astribanks reside.
- Replaces useless sysfs code that existed in the module.
- Currently used to set the sync source automatically at device
adition / removal.
* BRI: We do need the T1 timer in NT. If it gets into G2 state (rr4407).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2811 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Update to zaptel-1.2.18 and zaptel-1.4.3 (r4308 onward)
* Fix a critical race with zaptel synchronization (r4362)
* Added a /proc/xpp/cmds for statistics about command timing (r4360)
* Fix a digit mapping bug with hardware dtmf detection (r4357)
* In xpp/utils/Makefile add perl syntax checks to our scripts (r4337)
* Better USB data error checking (r4336)
* udev rules (xpp.rules) avoid false calls from wrong nodes (r4331)
* Improve hardware detection and reporting in lszaptel,
zaptel_hardware. zapconf is basically functional.
* Leds are blinked synchronously on all Astribanks now (r4262)
* Fix a BRI bug if OPTIMIZE_CHANMUTE was compiled into zaptel (r4258)
(This feature was not yet accepted into official zaptel)
* Removed compile warning about HZ != 1000 (r4218)
* Firmware updates.
* fpga_load now supports USB pathes without zeros (r4211)
* XPD numbers have changed to '<Unit><Subunit>' (r4196)
* Proper support for ZT_VMWI ioctl, if used in zaptel (r4092)
* Fix FXO power denial detection (r4054)
* FXO could accidentally go off-hook with some compilers (r4048)
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2732 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Add D-Channel TX, RX and BAD frames count in /proc/xpp/XBUS-*/XPD-*/bri_info
* Adjust output of xpp_sync script. Pad for 8 port BRI.
* Added a debugging module parport_debug (not compiled by default).
* Added an optional patch to zaptel:
- compiles only if ZAPTEL_SYNC_TICK is defined
- Allow interested driver to register for "sync" notification.
- Does not affect drivers that do not use this feature.
* Added external synchronization feature:
- Only if ZAPTEL_SYNC_TICK feature is compiled in
- Than XPP may be synchronized by another card (e.g: an Astribank
with FXS can be synchronized by a Digium PRI card).
- May be enabled/disabled in runtime via the 'sync_tick_active' module
parameter to the xpp.ko module.
* Fixed a potential bug in D-Channel hexdump printing.
* New visual indications in BRI leds:
- Constant ON RED/GREEN: Shows the port type -- NT/TE.
- Very fast "double blink": Layer1 work, no D-Channel yet.
- Steady blinking (1/2 sec): D-Channel trafic detected.
* xpp_fxloader moved to /usr/share/zaptel .
* adj_clock removed: never really used.
* Debugfs code now disabled by default.
* Now we have Zaptel::Hardware and a sample zaptel_hardware script (not
(installed by default).
* We also have a sample perl zapconf (not installed by default) which
aims at replacing genzaptelconf (sans the modules detection).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2529 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Protocol no. 2.6: syncing improvements.
* Support for 8-port Astribank BRI.
* Firmware unloading now works:
rmmod xpp_usb; /etc/hotplug/usb/xpp_fxloader reset
* Defaults of kernel parameters are now part of parameter description.
* World-readable kernel parameters.
* No need for extra patch beyond bristuff for Astribank BRI.
* Default poll intervals changed: 500 in BRI and FXO.
* Allow changing FXS polls interval at run time.
* BRI initalization fixed on SUSE (path to logger).
* When using the SUSE zaptel rpm package, set modules_var=ZAPTEL_MODULES in
/etc/sysconfig/zaptel .
* zt_registration not verbose by default.
* xpp_sync warns if FXO is sync slave.
* Fixed genzaptelconf -z (zapscan output emulation).
* PCM fixes.
* Solves "multiple ticks" bug. No need for pcm_tasklets workaround.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2475 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Version of xpp modules is set from xpp/.version, rather than "unknown".
* Astribank devices are now initialized in parallel: faster startup
when there are multiple Astribanks.
* Re-added support for the old format of /proc/xpp/sync write:
(echo N 0 > /proc/xpp/sync ) . The new format (SYNC=NN) is preffered.
* Firmware update to fix a PCM issue.
* Fixed a build issue with kernel 2.6.8 .
* Fixed missing initialization in Zaptel::Xpp::Xbus .
* genzaptelconf will now set FXS ports as LS by default. To set them as
KS, use fxs_default_start=ks in /etc/default/zaptel / /etc/sysconfig/zaptel
(Also a workaround for #7755 ).
* Groundwork for sync from zaptel master span: if zaptel is built with
ZAPTEL_SYNC_TIC (see zaptel/team/tzafrir/sync ), xpp will report its
drift from the zaptel sync master.
* USB firmware update: had bad lines checksums (and fxload did not report).
* fpga_load can now better report bad hex file checksum ;-) .
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2239 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* Reverse polarity and power denial detection.
* A short led flash at registration time.
* Add a real version of the xpp modules to them (independent of the Zaptel
version).
* Update our line status even when not registered.
* Fixed a false SIG_CHANGED when inserting or removing cable to FXO.
* Fixed compilation fixes for 2.6.20 (Bug #8982)
* A cleaner fix for the bool changes of 2.6.19 .
* Automatically detect echo_can_state_t at debug time.
* Automaitcally set XPP_DEBUGFS (depending on debugfs) at compile time.
* Bug-fixes to zaptel-helper.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@2113 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
XPS Init scripts renamed accordingly.
* Performance improvements for multi-XPD (span) devices.
* Astribank BRI driver (in next commit).
* Changes under /proc:
- XBUS and XPD numbers have two digits.
- Every script wildcard should be replaced from XBUS-? to XBUS-[0-9]*
- Added /proc/xpp/XBUS-*/XPD-*/blink: echo 1 to start and 0 to stop.
* Several countries (South Africa, UAE, anybody else) require a shorter
ring delay. Adjust FXO reg 0x17 (23)'s bits 0:2 to 011.
* Use tasklets to move most of the interrupt PCM copying out of the interrupt.
* Debugfs-based code to dump data to userspace (used to debug BRI D channel).
* Pretend every 2.6.9 actually has later RHEL's typedefs.
* fpga_load supports /dev/bus/usb .
* Fixed physical order sorting in genzaptelconf.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1966 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
be rebuilt every time a commit is made to any part of Zaptel
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1766 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
Intended for kernel 2.6.9 and earlier. Finally full support of 2.6.8 and 2.6.9.
r2937: diego | 2006-12-17 14:20:36 +0200
r2940: tzafrir | 2006-12-17 16:32:51 +0200
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1723 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
Merging xpp driver release 1.2 (rev. 2569), originally team/tzafrir/xpp_1.2
* Should build well. Almost final.
* genzaptelconf: Also work when zap_autoreg=0
* README.Astribank updated for rev. 1.2.
* xpp/utils/Makefile: Use $< with cc -c
* Get xpp/utils configuration from autoconf (without changesin top dir)
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1648 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1457 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
tries to access them afterwards causes Oops instead of unknown behaviour).
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1230 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
* FPGA firmware now loaded from PC (for newer models)
* Driver for the FXO module (xpd_fxo.ko)
* Moved most userspace files to the subdirectory utils (see also next commit)
* Explicit license for firmware files
* Optionally avoid auto-registration
* Registers initializations code is done by a userspace script.
* Remove obsolete .inc initialization files (we use user-space init)
* Added an install target to the utils dir.
* Updated README.Astribank accordingly.
* Using RBS signalling, as caller ID did not work well otherwise.
* Better handling of USB protocol errors.
* Fixed some procfs-related races.
* per-card-module ioctls.
* fxotune support.
* opermode support (set through /etc/default/zaptel for now)
* Userspace initialization script can also read registers.
* Power calibration works (and implemented in perl)
* some fine-tuning to the regster initialization parameters.
* Leds turn on before registration and turn off after it.
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@1212 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@995 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@994 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@973 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@958 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|
|
git-svn-id: http://svn.digium.com/svn/zaptel/branches/1.2@949 5390a7c7-147a-4af0-8ec9-7488f05a26cb
|