1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
#
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
#
# First come the span definitions, in the format
# span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow]
#
# The timing parameter determines the selection of primary, secondary, and
# so on sync sources. If this span should be considered a primary sync
# source, then give it a value of "1". For a secondary, use "2", and so on.
# To not use this as a sync source, just use "0"
#
# The line build-out (or LBO) is an integer, from the following table:
# 0: 0 db (CSU) / 0-133 feet (DSX-1)
# 1: 133-266 feet (DSX-1)
# 2: 266-399 feet (DSX-1)
# 3: 399-533 feet (DSX-1)
# 4: 533-655 feet (DSX-1)
# 5: -7.5db (CSU)
# 6: -15db (CSU)
# 7: -22.5db (CSU)
#
# The framing is one of "d4" or "esf" for T1 or "cas" or "ccs" for E1
#
# Note: "d4" could be referred to as "sf" or "superframe"
#
# The coding is one of "ami" or "b8zs" for T1 or "ami" or "hdb3" for E1
#
# E1's may have the additional keyword "crc4" to enable CRC4 checking
#
# If the keyword "yellow" follows, yellow alarm is transmitted when no
# channels are open.
#
#span=1,0,0,esf,b8zs
#span=2,1,0,esf,b8zs
#span=3,0,0,ccs,hdb3,crc4
#
# Next come the dynamic span definitions, in the form:
# dynamic=<driver>,<address>,<numchans>,<timing>
#
# Where <driver> is the name of the driver (e.g. eth), <address> is the
# driver specific address (like a MAC for eth), <numchans> is the number
# of channels, and <timing> is a timing priority, like for a normal span.
# use "0" to not use this as a timing source, or prioritize them as
# primary, secondard, etc. Note that you MUST have a REAL zaptel device
# if you are not using external timing.
#
# dynamic=eth,eth0/00:02:b3:35:43:9c,24,0
#
# Next come the definitions for using the channels. The format is:
# <device>=<channel list>
#
# Valid devices are:
#
# "e&m" : Channel(s) are signalled using E&M signalling (specific
# implementation, such as Immediate, Wink, or Feature Group D
# are handled by the userspace library).
# "fxsls" : Channel(s) are signalled using FXS Loopstart protocol.
# "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol.
# "fxsks" : Channel(s) are signalled using FXS Koolstart protocol.
# "fxols" : Channel(s) are signalled using FXO Loopstart protocol.
# "fxogs" : Channel(s) are signalled using FXO Groundstart protocol.
# "fxoks" : Channel(s) are signalled using FXO Koolstart protocol.
# "sf" : Channel(s) are signalled using in-band single freq tone.
# Syntax as follows:
# channel# => sf:<rxfreq>,<rxbw>,<rxflag>,<txfreq>,<txlevel>,<txflag>
# rxfreq is rx tone freq in hz, rxbw is rx notch (and decode)
# bandwith in hz (typically 10.0), rxflag is either 'normal' or
# 'inverted', txfreq is tx tone freq in hz, txlevel is tx tone
# level in dbm, txflag is either 'normal' or 'inverted'. Set
# rxfreq or txfreq to 0.0 if that tone is not desired.
# "unused" : No signalling is performed, each channel in the list remains idle
# "clear" : Channel(s) are bundled into a single span. No conversion or
# signalling is performed, and raw data is available on the master.
# "indclear": Like "clear" except all channels are treated individually and
# are not bundled. "bchan" is an alias for this.
# "rawhdlc" : The zaptel driver performs HDLC encoding and decoding on the
# bundle, and the resulting data is communicated via the master
# device.
# "fcshdlc" : The zapdel driver performs HDLC encoding and decoding on the
# bundle and also performs incoming and outgoing FCS insertion
# and verification. "dchan" is an alias for this.
# "nethdlc" : The zaptel driver bundles the channels together into an
# hdlc network device, which in turn can be configured with
# sethdlc (available separately).
# "dacs" : The zaptel driver cross connects the channels starting at
# the channel number listed at the end, after a colon
# "dacsrbs" : The zaptel driver cross connects the channels starting at
# the channel number listed at the end, after a colon and
# also performs the DACSing of RBS bits
#
# The channel list is a comma-separated list of channels or ranges, for
# example:
#
# 1,3,5 (channels one, three, and five)
# 16-23, 29 (channels 16 through 23, as well as channel 29
#
# So, some complete examples are:
# e&m=1-12
# nethdlc=13-24
# fxsls=25,26,27,28
# fxols=29-32
#
#fxoks=1-24
#bchan=25-47
#dchan=48
#fxols=1-12
#fxols=13-24
#e&m=25-29
#nethdlc=30-33
#clear=44
#clear=45
#clear=46
#clear=47
#fcshdlc=48
#dacs=1-24:48
#dacsrbs=1-24:48
#
# Finally, you can preload some tone zones, to prevent them from getting
# overwritten by other users (if you allow non-root users to open /dev/zap/*
# interfaces anyway. Also this means they won't have to be loaded at runtime.
# The format is "loadzone=<zone>" where the zone is a two letter country code.
#
# You may also specify a default zone with "defaultzone=<zone>" where zone
# is a two letter country code.
#
# An up-to-date list of the zones can be found in the file zaptel/zonedata.c
#
loadzone = us
#loadzone = us-old
#loadzone=gr
#loadzone=it
#loadzone=fr
#loadzone=de
#loadzone=uk
#loadzone=fi
#loadzone=jp
#loadzone=sp
#loadzone=no
defaultzone=us
|
