1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/*
* Zaptel configuration options
*
*/
#ifndef _ZCONFIG_H
#define _ZCONFIG_H
#ifdef __KERNEL__
#include <linux/config.h>
#include <linux/version.h>
#endif
/* Zaptel compile time options */
/*
* Uncomment to disable calibration and/or DC/DC converter tests
* (not generally recommended)
*/
/* #define NO_CALIBRATION */
/* #define NO_DCDC */
/*
* Boost ring voltage (Higher ring voltage, takes more power)
*/
/* #define BOOST_RINGER */
/*
* Define CONFIG_CALC_XLAW if you have a small number of channels and/or
* a small level 2 cache, to optimize for few channels
*
*/
/* #define CONFIG_CALC_XLAW */
/*
* Define if you want MMX optimizations in zaptel
*
* Note: CONFIG_ZAPTEL_MMX is generally incompatible with AMD
* processors and can cause system instability!
*
*/
/* #define CONFIG_ZAPTEL_MMX */
/*
* Pick your echo canceller: MARK2, MARK3, STEVE, or STEVE2 :)
*/
/* #define ECHO_CAN_STEVE */
/* #define ECHO_CAN_STEVE2 */
/* #define ECHO_CAN_MARK */
#define ECHO_CAN_MARK2
/* #define ECHO_CAN_MARK3 */
/*
* Uncomment for aggressive residual echo supression under
* MARK2 echo canceller
*/
/* #define AGGRESSIVE_SUPPRESSOR */
/*
* Define to turn off the echo canceler disable tone detector,
* which will cause zaptel to ignore the 2100 Hz echo cancel disable
* tone.
*/
/* #define NO_ECHOCAN_DISABLE */
/* udev support */
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
#define CONFIG_ZAP_UDEV
#endif
/* We now use the linux kernel config to detect which options to use */
/* You can still override them below */
#if defined(CONFIG_HDLC) || defined(CONFIG_HDLC_MODULE)
/* #define CONFIG_ZAPATA_NET */ /* NEVER implicitly turn on ZAPATA_NET */
#if LINUX_VERSION_CODE <= KERNEL_VERSION(2,4,19)
#define CONFIG_OLD_HDLC_API
#else
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,4,23)
/* Starting with 2.4.23 the kernel hdlc api changed again */
/* Now we have to use hdlc_type_trans(skb, dev) instead of htons(ETH_P_HDLC) */
#define ZAP_HDLC_TYPE_TRANS
#endif
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,3)
#define HDLC_MAINTAINERS_ARE_MORE_STUPID_THAN_I_THOUGHT
#endif
#endif
#endif
#ifdef CONFIG_PPP
#define CONFIG_ZAPATA_PPP
#endif
/*
* Uncomment CONFIG_ZAPATA_NET to enable SyncPPP, CiscoHDLC, and Frame Relay
* support.
*/
/* #define CONFIG_ZAPATA_NET */
/*
* Uncomment CONFIG_OLD_HDLC_API if your are compiling with ZAPATA_NET
* defined and you are using the old kernel HDLC interface (or if you get
* an error about ETH_P_HDLC while compiling).
*/
/* #define CONFIG_OLD_HDLC_API */
/*
* Uncomment for Generic PPP support (i.e. ZapRAS)
*/
/* #define CONFIG_ZAPATA_PPP */
/*
* Uncomment to enable "watchdog" to monitor if interfaces
* stop taking interrupts or otherwise misbehave
*/
/* #define CONFIG_ZAPTEL_WATCHDOG */
/* Tone zone info */
#define DEFAULT_TONE_ZONE 0
/*
* Uncomment for Non-standard FXS groundstart start state (A=Low, B=Low)
* particularly for CAC channel bank groundstart FXO ports.
*/
/* #define CONFIG_CAC_GROUNDSTART */
/*
* Uncomment if you happen have an early TDM400P Rev H which
* sometimes forgets its PCI ID to have wcfxs match essentially all
* subvendor ID's
*/
/* #define TDM_REVH_MATCHALL */
#endif
|
